Hytrol Catalog

CATALOG | 08312018 TW Horizontal Wire Mesh Belt Conveyor The Model TW with wire belt can carry hot or cold parts from ovens or freezers. Can be used in drying operations. • 3 Belt Widths • Wire Mesh Belt • Adjustable MS-Type Floor Supports Available 19-1/8" 6" DIA. DRIVE SPROCKETS 7" 1.9" DIA. RETURN IDLER BED LENGTH "L" OVERALL LENGTH "A" ALLOW 16" 11-1/8" MAX. 13-1/16" MAX. 20-1/8" "X" "X" 2-1/8" DIA. SNUB IDLER TAKE-UP 6" 4" DIA. TAIL PULLEY 2" OPTIONAL MS SUPPORTS SHOWN 33-3/16" 2" FLOW BED WIDTH BELT WIDTH 4" TREAD ROLLER TOTALLY ENCLOSED CHAIN GUARD 1.9" DIA. RETURN IDLER OR 2-1/8" DIA. SNUB IDLER 6-5/8" 7-3/8" FRAME SPACER • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BED –Slider bar in place of roller bed. BELT –Other widths than standard, galvanized low carbon steel, bright high carbon steel or stainless steel. 1 in. or 1/2 in. x 1/2 in. mesh available. Maximum product temperature 750 ° F with high carbon steel belt. BELT SPEED –Other constant and variable speeds. V-belt drive supplied on speeds under 15 FPM and with variable speeds. Note : Capacity affected with speed change. V-BELT DRIVE –V-belt supplied between motor and reducer. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). CEILING HANGARS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Energy efficient, single phase, brakemotor, other characteristics. 1 HP maximum. ELECTRICAL CONTROLS –Non-reversing magnetic starters and push-button stations. AC variable frequency drive. BELT –1/2 in. x 1 in. flat galvanized wire mesh belt. Maximum product temperature 350 ° F. BED –Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube spaced every 6 in. Mounted in 6 5/8 in. x 12 ga. powder painted formed steel channel frame bolted together with splice plates. END DRIVE –Located on discharge end of conveyor, chain guard on left hand side. CROSS BRACING –Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure tracking. (1) supplied in first 50' of bed section lengths and (1) per 50' of bed section length thereafter. Supplied in approximate center of lengths. DRIVE SPROCKETS –6 in. pitch dia. multiple cast iron sprockets with 1 3/16 in. dia. shaft 6 in. centers. TAIL PULLEY –4 in. dia. with 1 in. dia. shaft at bearings. Sprocket at each end. SNUB IDLER –Adjustable 2 1/8 in. dia. pre-lubricated ball bearings. RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated ball bearings. TAKE-UP –Take-ups at tail pulley. Provides 4 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning ball bearings on drive and tail shafts. Pre-lubricated ball bearings in tread rollers. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive sprocket. MOTOR –1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 75 lbs. NOT TO EXCEED capacity in chart. FLOOR SUPPORTS –Now supplied as optional equipment. • STANDARD SPECIFICATIONS SECTION X-X Conveyor shown with optional floor supports SIZE TO ORDER Overall Length "A" Bed Length "L" Belt Width 12" 18" 24" Bed Width 16" 22" 28" 6'-1" 5' WEIGHTS (Lbs.) 299 322 365 11'-1" 10' 368 415 465 16'-1" 15' 461 525 593 21'-1" 20' 530 608 693 26'-1" 25' 623 718 821 31'-1" 30' 692 801 921 41'-1" 40' 854 994 1149 51'-1" 50' 1023 1197 1391 61'-1" 60' 1185 1390 1609 71'-1" 70' 1355 1594 1862 81'-1" 80' 1517 1787 2090 91'-1" 90' 1697 1979 2319 101'-1" 100' 1841 2172 2547 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. LOAD CAPACITY CHART @ 65 FPM HP BEDWIDTHS–16" to 28" TOTAL LOAD (Lbs.) UP TO 50' UP TO 100' 1/2 850 350 1 1950 1500

RkJQdWJsaXNoZXIy NjQ0OTEy