Hytrol Catalog

CATALOG | 08312018 Transnorm Belt Curve Conveyor TS1500-140 The Model TS1500-140 provides a positive flow of products by means of a belt, driven by tapered pulleys. Conveyor is versatile in that it can transport a wide variety of products. Available in 45°,60°, 90°, and 180° turns. Other degrees available. Contact Transnorm. • 20 Belt Widths • Adjustable FSK-Type Floor Supports Available • Clipper Lacing F.O.B. Arlington, Texas "IR" CONVEYING SURFACE WIDTH "A" 90˚ "CL" (CSW) "A" "OR" 9.45" TOP OF BELT OAW CONVEYING SURFACE 11" 11" 4" 1-1/2" GUARD RAIL DRIVE OUTSIDE DRIVE OUTSIDE RIGHT HAND LEFT HAND LEFT HAND RIGHT HAND RIGHT HAND LEFT HAND 90˚ CURVES 180˚ CURVES 45˚ CURVES DRIVE OUTSIDE DRIVE OUTSIDE RIGHT HAND LEFT HAND 60˚ CURVES Conveyor shown with optional floor supports OAW Frame Conveying Surface Width Belt Width "IR" "CL" Radius (CS) "OR" 45° Weight (Lbs.) 60° Weight (Lbs.) 90° Weight (Lbs.) 180° Weight (Lbs.) 16 1/2" 11" 10" 34" 39 1/2" 45" 361 386 411 552 18 1/2" 13" 12" 32" 38 1/2" 365 390 414 567 20 1/2" 15" 14" 30" 37 1/2" 365 390 415 572 22 1/2" 17" 16" 28" 36 1/2" 367 392 417 577 24 1/2" 19" 18" 26" 35 1/2" 369 394 419 581 26 1/2" 21" 20" 36" 46 1/2" 57" 380 423 466 626 28 1/2" 23" 22" 34" 45 1/2" 388 438 487 659 30 1/2" 25" 24" 32" 44 1/2" 390 440 490 665 32 1/2" 27" 26" 54" 67 1/2" 81" 426 520 591 868 34 1/2" 29" 28" 52" 66 1/2" 428 524 596 877 36 1/2" 31" 30" 50" 65 1/2" 431 530 601 887 38 1/2" 33" 32" 48" 64 1/2" 434 533 606 896 40 1/2" 35" 34" 46" 63 1/2" 437 538 611 905 42 1/2" 37" 36" 44" 62 1/2" 439 542 616 13 44 1/2" 39" 38" 66" 85 1/2" 105” 481 621 706 1103 46 1/2" 41" 40" 64" 84 1/2" 485 627 713 1116 48 1/2" 43" 42" 62" 83 1/2" 488 633 720 1129 50 1/2" 45" 44" 60" 82 1/2" 491 639 726 1141 52 1/2" 47" 46" 58" 81 1/2" 494 644 732 1152 54 1/2" 49" 48" 56" 80 1/2" 497 649 738 1164 FLOW FLOW FLOW FLOW TYPE A LEFT HAND CURVE OUTSIDE DRIVE TYPE B RIGHT HAND CURVE OUTSIDE DRIVE TYPE C LEFT HAND CURVE INSIDE DRIVE TYPE D RIGHT HAND CURVE INSIDE DRIVE Applies to all degree of curves. All locations are standard for Transnorm. Specify location. BELT –Black Rough Top (Inverted Pyramid) Self Extinguishing Belt with Guide Strip FRAME –9.45 in. deep x 40 mm x 40 mm aluminum extrusion. PULLEYS –Tapered with 1 7/16 in. dia. shaft through bearings. Adjustable to control belt tension. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulley. Re-lube type. MOTOR – 3/4 HP Shaft Mounted Right Angle Gearmotor 208/230/460/575V-3Ph. 60 Hz (Specify Exact Voltage). BELT SPEED –Constant 65 FPM at center line of conveying surface. CAPACITY –Maximum load per linear foot (measured at center line of conveying surface) 40 lbs. FLOOR SUPPORTS –Now supplied as optional equipment. See chart below for available elevations. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –FSK Type floor supports are available with a wide range of adjustment. Specify top of belt elevation. Supports required at each end and in the center of the conveyor. Holes in feet for lagging to floor. Knee braces recommended above FSK-6 support. BELT SPEED –Up to 250 FPM (shaft mounted), 251 - 600 FPM (timing belt), NOTE: Capacity affected with speed change, see chart above. Higher speeds available, contact factory. DRIVE LOCATION –Specify. MOTORS –Other HP available, 5 HP maximum (contact factory). BELTS –Types and styles other than standard are available (contact factory). CEILING HANGERS –Includes mouting brackets and cross pipes only. GUARD RAILS –3 in. to 24 in. tall available for all sizes. The outside guard rail is always supplied. The inside guard rail is supplied unless no guard rail is specified. ELECTRICAL CONTROLS –Non-reversing magnetic starters and push-button stations. AC variable frequency drive. CUSTOM COLORS –Available (contact factory). Paint chip must be provided. • STANDARD SPECIFICATIONS For warranty/spare parts contact Transnorm System’s customer service. Please provide Transnorm’s serial number. Transnorm System Inc. 2810 Avenue E East Arlington, TX 76011 Phone: 1-800-331-1749 X 249 Fax: (972) 606-0768

RkJQdWJsaXNoZXIy NjQ0OTEy