Hytrol Catalog

CATALOG | 08312018 Conveyor shown with optional floor supports TL Heavy Duty Horizontal Belt Conveyor The Model TL with its rugged, heavy duty construction is ideally used for long assembly line operations, inspections, testing, sorting, and packing. Can be floor supported or ceiling hung. • 6 Belt Widths • Reversible (with center drive) • Rugged Construction • Adjustable MS-Type Floor Supports Available FLOW 2-1/2" DIA. SNUB IDLER 8" DIA. DRIVE PULLEY 17" NIP POINT GUARD 19-1/8" MAX. 2" OPTIONAL MS-D SUPPORT SHOWN 11-1/4" ALLOW 16" 13-1/4" MAX. 2-1/8" DIA. SNUB IDLER TAKE-UP NIP POINT GUARD 6" DIA. TAIL PULLEY "X" "X" OVERALL LENGTH "A" BED LENGTH "L" 8" OPTIONAL MS SUPPORT SHOWN 37-1/2" MAX. 11-15/16" MAX. 1.9" DIA. RETURN IDLER 24-1/4" BED WIDTH BELT WIDTH 2-1/8" DIA. SNUB IDLER TOTALLY ENCLOSED CHAIN GUARD 4" FRAME SPACER 6-5/8" L.H. SIDE R.H. SIDE SIZE TO ORDER Overall Length "A" 6" Dia. Tail Pulley Bed Length "L" Overall Length with Center Drive Belt Width 24" 30" 36" 42" 48" 52" BedWidth 30" 36" 42" 48"* 54"* 58"* 7'-1" 5’ 6'-4" WEIGHTS (Lbs.) 375 N/A N/A N/A N/A N/A 12'-1" 10’ 11'-4" 475 555 615 888 974 1060 17'-1" 15’ 16'-4" 625 686 752 1084 1191 1298 22'-1" 20’ 21'-4" 725 796 867 1280 1408 1536 27'-1" 25’ 26'-4" 875 967 1065 1476 1625 1774 32'-1" 30’ 31'-4" 975 1077 1180 1672 1842 2012 37'-1" 35’ 36'-4" 1125 1248 1377 1868 2059 2250 42'-1" 40’ 41'-4" 1225 1358 1492 2064 2276 2488 47'-1" 45’ 46'-4" 1375 1529 1690 2260 2493 2726 52'-1" 50’ 51'-4" 1475 1639 1805 2456 2710 2964 57'-1" 55’ 56'-4" 1625 1810 2002 2652 2927 3202 62'-1" 60’ 61'-4" 1725 1920 2117 2848 3144 3440 67'-1" 65’ 66'-4" 1875 2091 2315 3044 3361 3678 72'-1" 70’ 71'-4" 1975 2201 2430 3240 3578 3916 77'-1" 75’ 76'-4" 2125 2372 2627 3436 3795 4154 82'-1" 80’ 81'-4" 2225 2482 2742 3632 4012 4392 87'-1" 85’ 86'-4" 2375 2653 2940 3828 4229 4630 92'-1" 90’ 91'-4" 2479 2763 3055 4024 4446 4868 97'-1" 95’ 96'-4" 2625 2934 3252 4220 4663 5106 102'-1" 100’ 101'-4" 2725 3044 3367 4416 4880 5334 NOTE: • All weights in catalog are CONVEYORWEIGHTS ONLY. Accessories, crating, etc., are not included. • *5’-0”Bed, V-Belt Drive Only • 36”BedWidth - 1Week Stockyard . SECTION “X-X” CATALOG | 08312018 TL BELT –Ultimate 140 BBS–Nitrile. BED –6 5/8in. deep x 12 ga. formed steel slider bed powder painted. Reinforced with 3/4in. pipe which forms sockets for guard rails. Standard 5 ft. & 10 ft. long sections bolt together with splice plates. 48 in. and 51 in. bed widths are available in 5 ft. lengths only. END DRIVE –Located on discharge end of conveyor, chain guard on left hand side. DRIVE PULLEY –8 in. dia. with 1 3/16 in. dia. shaft at bearings, machine crowned and fully lagged. TAIL PULLEY –6 in. dia. with 1 3/16 in. dia. shaft at bearings, machine crowned. SNUB IDLER –Adjustable 2 1/8 in. dia. for tail end 2 1/2 in. dia. for drive end. Pre-lubricated ball bearings. Guards included. RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated ball bearings. TAKE-UP –Take-ups at tail pulley. Provides 4 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive pulley. MOTOR–1 HP –208/230/460/575V–3 Ph.–60 Hz. Premium Energy Efficient C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 100 lbs. NOT TO EXCEED capacity in charts. FLOOR SUPPORTS –Now supplied as optional equipment. FLOOR SUPPORTS –MSType floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BELT* –White Polymate 100 RMP-COS (cover one side), Black Trackmate 120 Roughtop with PVC cover, Brown Polymate Roughtop w/Nitrile cover, Black Trackmate 533 COS-PVC, Tan Glidetop, Pure Gum Rubber Roughtop. BELT SPEED* –Other constant and variable speeds. V-belt drive supplied on speeds under 17 FPM. OVERHEAD END DRIVE –Motor-reducer unit mounted 9 1/2 in. above belt. Other clearances available, specify. (Chain guard right hand side). Minimum elevation–10 in. SIDE MOUNTED END DRIVE –Motor-reducer unit mounted left hand side of conveyor. Minimum elevation 10 in. CENTER DRIVE –Provides 16 in. of belt take-up. Minimum elevation 20 in. Specify location. Minimum OAL 66 in. LOW ELEVATION SIDE MOUNTED CENTER DRIVE –Motor-reducer unit mounted to side of conveyor. Minimum elevation 16 1/2 in. S TACKED END DRIVE –Contact factory for minimum elevations. V-BELT DRIVE –V-Belt supplied between motor and reducer. Minimum overall drive width 14 in. Allow 65 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). UNDERSIDE TAKE-UP –Provides 16 in. of belt take-up. Extends down 15 3/4 in. from top of belt. NOSEOVER* –Adjustable, single (0 ° to 15 ° ), double (0 ° to 30 ° ). LOWER POWERED FEEDER* –Chain type driven from tail pulley of inclined conveyor. Underside take-up required when end drive is used. MS-Type floor supports now supplied as optional equipment. 8 in. dia. drive recommended on conveyor when feeder exceeds 44 1/2 in. OAL–50 1/2 in. OAL with system end. BUTT COUPLINGS –Provides connection to SB, RB, LR, ACC, ACZ, ABEZ, 190-NSP, 190-NSPEZ, 20- CR, 1.9 in. & 2.0 in. gravity conveyors. Includes 1 in. dia. pop out roller. Center drive or underside take-up recommended. SYSTEM END ROLLER –12 in. long tail sections provide connection to: SB, RB, LR, ACC, ACZ, ABEZ, 190 NSP, 190-NSPEZ, 1.9 in. & 2.0 in. gravity conveyors. Includes 1.9 in. dia. pop-out transfer roller. Belt width is 6 in. less than bed width. Center drive or underside take-up required. GUARD RAILS –Adjustable Universal Channel Guard Rail, solid side guards, PC side guards with formed top.. Fixed Channel overlapping, one direction (use with systems ends only). Fixed Channel non-overlapping, reversing (use with system ends only). CASTERS –See Accessory section. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –One direction manual start switch, reverse drum switch, non-reversing and reversible magnetic starters, push button stations. AC variable frequency drive. *NOTE: Capacity affected with these options. • OPTIONAL EQUIPMENT 8" DIA. DRIVE PULLEY HORIZONTAL LIVE LOAD CAPACITY @ 65 FPM HP BELT WIDTHS TO LENGTHS UP TO 52' 102' DISTRIBUTED LOAD (LBS.) 1 24" - 30" 530 350 36" - 42" 450 250 48" - 52" 360 100 2 24" - 30" 1250 1100 36" - 42" 1200 950 48" - 52" 1100 850 • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy