Hytrol Catalog

CATALOG | 08312018 TH Trash Belt Conveyor Designed to handle empty cardboard boxes and paper trash. • 8 Belt Widths • Center Drive • Adjustable MS-Type Floor Supports Available • Integral Side Guards • Underside Bed Cover Full Length Conveyor shown with optional floor supports OVERALL FRAME WIDTH BETWEEN RAIL WIDTH BELT WIDTH 3-1/8" 1/2" 6" TOTALLY ENCLOSED CHAIN GUARD UNDERSIDE BED COVER SIZE TO ORDER Overall Length "A" Bed Length "L" Belt Width 11 1/2" 17 1/2" 23 1/2" 29 1/2" 35 1/2" 41 1/2" 47 1/2" 53 1/2" Between Rail Width 13" 19" 25" 31" 37" 43" 49" 55" Overall FrameWidth 16" 22" 28" 34" 40" 46" 52" 58" 12' 10' WEIGHTS (Lbs.) 732 867 1002 1137 1272 1408 1542 1676 22' 20' 974 1152 1330 1508 1686 1865 2042 2219 32' 30' 1216 1437 1658 1879 2100 2322 2542 2762 42' 40' 1458 1722 1986 2250 2514 2779 3042 3305 52' 50' 1700 2007 2314 2621 2928 3236 3542 3848 62' 60' 1942 2292 2642 2992 3342 3693 4042 4391 72' 70' 2184 2577 2970 3363 3756 4150 4542 4934 82' 80' 2426 2862 3298 3734 4170 4607 5042 5477 92' 90' 2668 3147 3626 4105 4584 5064 5542 6020 102' 100' 2910 3432 3954 4476 4998 5521 6042 6563 112' 110' 3152 3717 4282 4847 5412 5978 6542 7106 122' 120' 3394 4002 4610 5218 5826 6435 7042 7649 132' 130' 3636 4287 4938 5589 6240 6892 7542 8192 142' 140' 3878 4572 5266 5960 6654 7349 8042 8755 152' 150' 4120 4857 5594 6331 7068 7806 8542 9278 ADD TO ABOVEWEIGHTS FOR THE FOLLOWING ACCESSORIES: • Noseover with 2 pulley hitch 138 172 206 240 274 308 342 376 • Other guard rails - pair - 6" high x 10' lg. 32 32 32 32 32 32 32 32 • Per 10' Int. section with support & belt 242 285 328 371 414 457 500 543 Above weights include 6" high guards, MS-6 supports, and 8" center drive. Accessories, crating, etc., are not included. OVERALL LENGTH "A" BED LENGTH "L" 8" DIA. DRIVE PULLEY 6" TAKE-UP PULLEY "X" "X" 2-1/2" SNUB IDLER 62 " 38-1/4" 21" ALLOW 16" 10-3/4” 2-1/2" SNUB IDLER OPTIONAL MS-SUPPORTS SHOWN 14" 8-1/2" 4" & 6" DIA. TAIL PULLEY 12" TOTALLY ENCLOSED BELT GUARD PREFERRED FLOW (ALLOW 65” WITH V-BELT DRIVE) SECTION “X-X” CATALOG | 08312018 TH BELT –Horizontal units: Ultimate 140 BBS–Nitrile. BED –14 ga. formed steel slider bed bolted between two 7 1/2 in. deep x 12 ga. formed steel side channels with 6 in. high guards. Standard 5, 6, 7, 8, 9, and 10 ft. long sections. CENTER DRIVE –Minimum elevation–16 11/16 in. Can be placed on any section of conveyor length. Minimum OAL without modification 12 ft. 0 in. Chain guard located on left hand side. DRIVE PULLEY –8 in. dia. with 1 7/16 in. dia. shaft at bearings, fully lagged. TAIL PULLEY –4 in. dia. with 1 in. dia. shaft at bearings, machine crowned 13 in., 19 in., and 25 in. BR up to 150 ft. long. 6 in. dia. with 1 3/16 in. dia. shaft at bearings, machine crowned all other applications. SNUB IDLER –Adjustable 2 1/8 in. dia. with HD pre-lubricated ball bearings. RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated bearings. BEARINGS –Sealed, pre-lubricated, self-aligning, cast-iron ball bearings on drive and tail pulleys. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50, 60 or 80 roller chain to drive pulley depending on speed and length. MOTOR –1 HP–208/230/460/575V–3 Ph.–60 Hz. Premium Energy Efficient C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 10 lbs. DUST PANS –Solid 16 ga. underside dust covers held in place by 1/4 turn screws for easy removal. FLOOR SUPPORTS –Now supplied as optional equipment. FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BELT –Inclined units: BlackTrackmate 120 Roughtopwith PVC cover. Recommended but not required. Contact Factory for Application Information. BELT SPEED –Others constant or variable. END DRIVE –8 in. side mounted end drive with underside takeup. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). NOSEOVER –(10 ° , 12 1/2 ° , 15 ° ) Fixed single nose for transition of product from incline to horizontal. TWO-PULLEY HITCH –For transition of product from horizontal to incline (10 ° , 12 1/2 ° , 15 ° ). POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –One direction manual start switch, non-reversing starters, push button stations. AC variable frequency drive. SIDE GUARDS –Available 12 in. to 24 in. high vertical. Flared guards available on 6 in. and 12 in. high only. MANUAL UNDERSIDE TAKE–UP –Provides 16 in. of belt take-up up to 150 ft.. PNEUMATIC UNDERSIDE TAKE–UP –Provides 60 in. of belt take-up for conveyors over 151 ft. • OPTIONAL EQUIPMENT NOSEOVER GUARD RAILS FLOOR SUPPORTS BELT TWO-PULLEY HITCH LOAD CAPACITY CHART @ 65 FPMWITH STANDARD BELT HP OVERALL FRAME WIDTH TO TOTAL LOAD LBS. OVERALL LENGTH 50' 75' 100' 150' 1 28" 550 470 395 240 40" 460 345 230 – 52" 370 215 – – 58" 360 200 – – 2 28" 1275 1200 1125 970 40" 1190 1075 960 730 52" 1100 945 795 490 58" 1000 900 700 400 LOAD CAPACITY CHART INCLINE @ 65 FPM w/ROUGHTOP BELT HP OVERALL FRAME WIDTH TO 8 FEET LIFT 12 FEET LIFT OVERALL LENGTH OVERALL LENGTH 50' 75' 100' 150' 50' 75' 100' 150' 1 28" 380 350 310 190 330 320 290 180 40" 310 250 170 – 270 230 150 – 52" 240 140 – – 210 130 – – 58" 200 – – – – – – – 2 28" 500 750 920 840 500 750 850 790 40" 500 750 780 620 500 750 720 590 52" 500 720 630 400 500 650 580 380 58" 500 500 500 500 500 500 500 500 • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy