Hytrol Catalog

CATALOG | 08312018 6" FLOW 2-1/8" DIA. SNUB IDLER 4" DIA. DRIVE PULLEY 6" 4-9/16" NIP POINT GUARD 15-5/8" MAX. 2" 22" OPTIONAL MS SUPPORT SHOWN 35-1/4" ALLOW 16" 11-1/16" 13-1/4" MAX. 2-1/8" DIA. SNUB IDLER 2" NIP POINT GUARD 4" DIA. TAIL PULLEY "X" "X" OVERALL LENGTH "A" BED LENGTH "L" TAKE-UP 1.9" DIA. RETURN IDLER SIZE TO ORDER Overall Length "A" Bed Length "L" Overall Length with Center Drive Drive Pulley Belt Width 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 30" Bed Width 10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 6’ 5’ 6’ 4" Dia. WEIGHTS (Lbs.) 239 252 262 272 282 305 315 343 366 374 389 11’ 10’ 11’ 271 286 300 314 328 368 382 397 422 431 447 16’ 15’ 16’ 324 343 362 380 398 456 475 494 528 540 562 21’ 20’ 21’ 354 377 400 422 444 519 542 565 607 621 649 26’ 25’ 26’ 406 434 461 488 514 607 635 662 713 730 764 31’ 30’ 31’ 436 468 499 530 560 670 702 733 792 812 851 36’ 35’ 36’ 488 525 560 596 630 758 795 830 898 921 966 41’ 40’ 41’ 519 559 599 638 677 821 862 901 977 1002 1053 46’ 45’ 46’ 570 616 660 704 747 909 955 998 1083 1112 1168 51’ 50’ 51’ 605 655 704 753 801 982 1032 1081 1176 1208 1271 56’-11” 55’ 56’ 8" Dia. WEIGHTS (Lbs.) 652 712 795 819 871 1070 1125 1178 1282 1317 1386 61’-11” 60’ 61’ 688 746 804 861 918 1133 1192 1249 1351 1385 1453 66’-11” 65’ 66’ 734 803 865 927 988 1221 1285 1346 1457 1494 1568 71’-11” 70’ 71’ 772 839 905 971 1036 1287 1364 1420 1549 1589 1678 76’-11” 75’ 76’ 816 896 966 1037 1106 1375 1457 1517 1655 1701 1793 81’-11” 80’ 81’ 855 930 1005 1079 1153 1438 1514 1588 1734 1783 1880 86’-11” 85’ 86’ 898 987 1066 1145 1223 1526 1607 1685 1840 1892 1995 91’-11” 90’ 91’ 937 1021 1104 1187 1269 1589 1673 1756 1920 2139 2084 96’-11” 95’ 96’ 980 1078 1165 1253 1339 1677 1766 1853 2026 2084 2199 101’-11” 100’ 101’ 1020 1112 1204 1295 1386 1740 1833 1924 2105 2166 2286 NOTE: • All StandardWidths to be Offered in 1 ft. Length Increment. • All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. • 3 Day Delivery on 16", 18", 24" and 28". All other widths are 2 weeks. 8” END DRIVE OVERALLLENGTH "A" BED LENGTH "L" 14-9/16" MAX. ALLOW 16" 13-1/4" MAX. 37-1/4" MAX. OPTIONAL MS-D SUPPORT SHOWN 24" 19-1/8" MAX. 9-9/16" 11-1/4" 8" DIA. DRIVE PULLEY 2-1/2" DIA. SNUB IDLER 17" NIP POINT GUARD FLOW 4” END DRIVE BED WIDTH BELT WIDTH FORMED STEEL BED 2-1/8" DIA. SNUB IDLER TOTALLY ENCLOSED CHAIN GUARD 4" 4" SECTION “X-X” 8-3/8” REF 6-15/32” 4-7/8” MIN ELEV FEATURED OPTION: SHAFT MOUNTED DRIVE SHOWN MOUNTED HORIZONTAL 6-1/2” REF 4” 3” SPEED CHART FOR SHAFT MOUNED END DRIVE ON TAWITH 4 IN. DIA. DRIVE PULLEY SPEED FPM MAX HP 34 1/2 41 1/2 52 1/2 68 1 82 1 103 1 138 1 206 1 274 1 412 1 Conveyor shown with featured option - shaft mounted end drive A very versatile conveyor, the Model TA can be used in many types of material handling situations such as assembly line operations, sorting, packing, and inspection. Conveyor sets up quickly and easily to save on installation time. • 10 Belt Widths • Reversible (with center drive) • Smooth, Slim Bed • Adjustable MS-Type Floor Supports Available Horizontal Belt Conveyor TA Conveyor shown with optional floor supports. CATALOG | 08312018 TA LOAD CAPACITY CHART @ 65 FPMW/STANDARD BELT LENGTHS UP TO HP BELT WIDTHS TO 4" Dia. Drive Pulley 8" Dia. Drive Pulley 11' 21' 31' 41' 51' 77' 102' DISTRIBUTED LOAD (LBS.) 1/2 6"-16" 335 320 310 300 285 260 230 18"-28" 320 300 285 270 255 210 170 1 6"-16" 650 635 625 615 605 625 595 18"-30" 635 620 600 585 570 580 540 LOAD CAPACITY CHART 25° INCLINE @ 65 FPMW/ROUGHTOP BELT HP BELT WIDTHS TO LENGTHS UP TO 11' 21' 31' 41' 51' DISTRIBUTED LOAD (LBS.) 1/2 6"-16" 155 145 135 125 110 18"-28" 145 130 115 100 80 1 6"-16" 310 300 290 280 270 18"-30" 305 285 270 255 240 FLOOR SUPPORTS –MSType floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BELT* –White Polymate 100 RMP-COS (cover one side), Black Trackmate 120 Roughtop with PVC cover, Brown Polymate Roughtop w/Nitrile cover, Black Trackmate 533 COS-PVC, Tan Glidetop, Pure Gum Rubber Roughtop. BELT SPEED* –Other constant and variable speeds. V-belt drive supplied under 17 FPM. SHAFT MOUNTED END DRIVE –Motor reducer unit mounted on extended drive pulley shaft. Can be mounted with motor horizontal for 4 7/8 in. minimum elevation. Mounting bracket and torque arm allows for multiple mounting positions. 4 in. drive only. See chart page 5 for speeds. OVERHEAD END DRIVE –Motor-reducer unit mounted 9 1/2 in. above belt. Other clearances available, specify. (Chain guard right hand side). Minimum elevation 6 in. with 4 in. drive, 10 in. with 8 in. drive. SIDE MOUNTED END DRIVE –Motor-reducer unit mounted on left hand side of conveyor. Minimum elevation 7 in. with 4 in. drive, 10 in. with 8 in. drive. CENTER DRIVE –Provides 16 in. of belt take-up. Minimum elevation 16 in. with 4 in. drive, 17 in. with 8 in. drive. Specify location. Minimum OAL without modification–66 in. with 4 in. drive, 66 in. with 8 in. drive. Belt width is 6 in. less than bed width. LOW ELEVATION SIDE MOUNTED CENTER DRIVE –Motor-reducer unit mounted to side of conveyor. Minimum elevation 13 1/2 in. with 4 in. or 8 in. drive. Belt width is 6 in. less than bed width. STACKED END DRIVE –Minimum elevation 27 3/4 in. with V-belt drive, 33 3/4 in. with C-Face drive. V-BELT DRIVE –V-Belt supplied between motor and reducer. Minimum overall drive width 14 in. Allow 65 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). UNDERSIDE TAKE-UP –Provides 16 in. of belt take-up. Extends down 13 1/8 in. from top of belt. Belt width is 6 in. less than bed width. SIDE TABLES –Powder painted 14 ga. formed steel table, 10 in., 16 in., or 22 in. wide from side of bed. One or both sides. GUARD RAILS –Universal adjustable universal channel, solid side guards, PC side guards with formed top. Fixed Channel overlapping, one direction (use with systems ends only). Fixed Channel non-overlapping, reversing (use with system ends only). NOSEOVER* –Adjustable, single (0° to 15°), double (0° to 30°). LOWER POWERED FEEDER* –Chain type driven from tail pulley of inclined conveyor. Underside take-up required when end drive is used. MS-Type floor supports now supplied as optional equipment. 8 in. dia. drive recommended on conveyor when feeder exceeds 44 1/2 in. OAL–50 1/2 in. OAL with system end. GRAVITY BRACKETS –Adjustable bars with 1 in. dia. pop-out transfer roller to attach wheel or 1 3/8 in. roller conveyor. Available 12 in. to 28 in. bed widths only. BUTT COUPLINGS –Provides connection to SB, RB, LR, ACC, ACZ, ABEZ, 190-NSP, 190-NSPEZ, 1.9 in. & 2.0 in. gravity conveyors. Includes 1 in. dia. pop-out roller. Center drive or underside take-up recommended. SYSTEM END ROLLER –12 in. long tail sections provide connection to SB, RB, LR, ACC, ACZ, ABEZ, 190-NSP, 190-NSPEZ, 1.9 in. & 2.0 in. gravity conveyors. Includes 1.9 in. dia. pop-out transfer roller. Belt width is 6 in. less than bed width. (Center drive or underside take-up required.) Not available on 10 in. bed. PULLEYS –6 in. tail with 1 3/16 in. dia. shaft at bearings, or 8 in. drive with 1 3/16 in. dia. shaft at bearings. CASTERS –See Accessory section. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Energy efficient, single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –One direction manual start switch, reverse drum switch, non-reversing and reversible magnetic starters, push button stations. AC variable frequency drive. * NOTE: Capacity affected with these options. BELT –Ultimate 140 BBS–Nitrile. BED –4 in. deep x 12 ga. formed steel slider bed- powder painted. Standard 5 ft. & 10 ft. long sections bolt together with splice plates. END DRIVE –Located on discharge end of conveyor, chain guard on left hand side. DRIVE PULLEY –4 in. dia. with 1 in. dia. shaft at bearings or 8 in. dia. with 1 3/16 in. dia. shaft at bear- ings, machine crowned and fully lagged. See chart. TAIL PULLEY –4 in. dia. with 1 in. dia. shaft at bearings, machine crowned. SNUB IDLER –Adjustable 2 1/8 in. dia. for 4 in. pulley–2 1/2 in. dia. for 8 in. pulley. Pre-lubricated ball bearings. Guards included. RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated ball bearings. TAKE-UP –Take-ups at tail pulley. Provides 4 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive pulley. MOTOR –1/2 HP–208/230/460V/575–3 Ph.–60 Hz. Totally Enclosed C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 75 lbs. NOT TO EXCEED capacity in charts. FLOOR SUPPORTS –Now supplied as optional equipment. • STANDARD SPECIFICATIONS • OPTIONAL EQUIPMENT

RkJQdWJsaXNoZXIy NjQ0OTEy