Hytrol Catalog

CATALOG | 08312018 OAW 18” THRU 22” BR 15” THRU 19” OAW 24” THRU 42” BR 21” THRU 39” 6-1/2 12-1/2 6-1/2 12-1/2 A B C B D 15/32 2-3/4 3MIN INT 18MINTAIL Reversing O-Ring Transfers are used to move products at right angles to adjacent or parallel conveyor lines. An air bag lifts the transfer mechanism while powered O-Rings transfer the product. Linear bearings are used to guide transfer as it is raised and lowered. A gearmotor is utilized to operate the reversing mechanism to reverse transfer flow. Can be used with Models 138 and 190 NSP/NSPEZ line shaft conveyors. Chain Transfers are used to move products at right angles to adjacent or parallel conveyor lines. One air cylinder lifts the transfer mechanism while powered chains transfer the product. Chains run on UHMW polyethylene wearstrips to reduce friction. Complete unit mounts in Models ABEZ, 190-ACZ or 190-LR. CAPACITY –75 lbs. maximum unit load. TRANSFER O-RING –3/8 in. dia. polyurethane o-ring. TRANSFER SPEED –Not to exceed speed of conveyor. DRIVE –Transfer is driven from 230/460/3/60, 1/2 HP shaft-mounted gearmotor. MOUNTING –Mounted in 48 in. long section of 138-NSP, 190-NSP, 138-NSPEZ, 190-NSPEZ with 3 and 4 in. roller centers. ELECTRICAL CONTROLS –Not furnished as standard equipment. PNEUMATICS –Air bag (controlled by single solenoid valve) lifts transfer. Requires maintained electrical signal of 115V–1 Ph. 60 Hz. from photo cell, proximity switch, etc. (not supplied). Transfer will stay in raised position until signal is broken. Current consumption is .09 amps holding. AIR REQUIREMENTS –Minimum pressure 60 P.S.I., maximum 100 P.S.I. with .038 cu.ft. of free air per cycle at 60 P.S.I. NOTE : To eliminate contaminants in air supply line, a filter-regulator should be installed prior to air valve (not supplied as standard). AIR BAG ACTUATOR LINEAR BEARING 1-1/2" 1-1/2" 3" 3" 4" 4" 4" 4" 4" 4" 4-1/4" 4-1/4" 6-3/4" 4" 3" 3" 3" 3" TRANSFER CL S E F O N E F N O S E F N O S N S F E O 16” 13” 9-1/2” 1/4” 24” 21” 9-1/2” 1/4” O E N F S N S F E O N O S E F S O N F E F S O N E 21"-39" BR 13” - 19” BR and 138-NSP 12-7/8” MINIMUM ELEVATION 17-1/2” MINIMUM ELEVATION 24” 48” Note : No accumulation in transfer section. REVERSING O-RING TRANSFER (BR TYPE) CHAIN TRANSFER (CT-200) NOTE : No brakes in ABEZ zone where CT-200 is mounted. A B D C STRAND CODES STRAND QTY STRAND CENTERS A B C D E F G H J K L M N P 2 2 2 3 2 2 3 4 2 4 2 3 4 4 6 9 12 6,6 15 18 9,9 6, 6, 6 21 6, 9, 6 24 12, 12 6, 12, 6 9, 6, 9 06” 09” 12” 12” 15” 18” 18” 18” 21” 21” 24” 24” 24” 24” N/A N/A N/A 6” N/A N/A 9” 6” N/A 6” N/A 12” 6” 9” N/A N/A N/A N/A N/A N/A N/A 6” N/A 9” N/A N/A 12” 6” 18-1/2” 21-1/2” 24-1/2” 24-1/2” 27-1/2” 30-1/2” 30-1/2” 30-1/2” 33-1/2” 33-1/2” 36-1/2” 36-1/2” 36-1/2” 36-1/2” 138-NSP OAW BR 15" 13" 18" 16" 24" 22" 190-NSP OAW BR 16" 13" 18" 15" 20" 17" 22" 19" 24" 21" 26" 23" 28" 25" 30" 27" 34" 31" 36" 33" 40" 37" 42" 39" • STANDARD SPECIFICATIONS SYSTEMS ACCESSORIES CATALOG | 08312018 STRAND CENTERS EFFECTIVE OAL 1-1/2" 1-1/2" 1-3/4" 5-1/2" CONVEYING SURFACE OAW "A" GEARMOTOR 3-1/2" DIA ROLLER #C-2060-H CHAIN FROM DRAG CHAIN CONVEYOR 10" Nominal The 35 Roller Transfer is mounted in a Model DC-60 or DCEZ-60 and is used to transfer product from one DC-60 to another DC-60. The 35 Roller Transfer uses 3 1/2” dia x 9 ga. rollers mounted on 6” centers. Air bags lift the transfer mechanism. The 35 Roller Transfer uses a 1/3 HP gearmotor to provide constant 30 FPM. 35 ROLLER TRANSFER STRAND CENTERS EFFECTIVE OAL 1-1/2" 1-1/2" 1-3/4" 5-1/2" CONVEYING SURFACE OAW "A" GEARMOTOR 3-1/2" DIA ROLLER #C-2060-H CHAIN FROM DRAG CHAIN CONVEYOR 10" Nominal NOTE: Extended Type & onveyor to Conveyor Type available, contact factory. MAXIMUM LOAD 3000 LBS. AT 30 FPM The 26 CRPT is used to rotate products up to 360 degrees. The turntable is powered by a shaft mounted gearmotor complete with variable speed controller for soft start/stop and has proximity switches mounted on the base to sense position and control rotation of product. Turntable speed is 3 Revolutions per minute with a 1 HP 460/3/60 gearmotor. An 8-wire collector ring allows unlimited rotation of turntable. Powered transition rollers, mounted on apron of turntable deck, help move product onto and off of turntable. The 26 CRR section has a Side Mounted Drive contained within the turning radius of the turntable. Standard speed is 30 FPMwith 1/2 HP 460/3/60 gearmotor. The tread rollers are 2 5/8 in. diameter with 7 gauge wall on 4 in. roller centers and have 2 5/8 in. dia. x .219 wall drive rollers with heavy duty bearings. Also available; gravity transition rollers; external transition roller sections (mounted to mating conveyors to fill in gap created by radius of turntable). Minimum Elevation - 16 inches. 26-CRPT POWER ROTATED TURNTABLE SIDE MOUNTED DRIVE GEARMOTOR OAL "A" POWERED TRANSITION ROLLERS OAW BR CS SIDE MOUNTED DRIVE GEARMOTOR OAL "A" POWERED TRANSITION ROLLERS 16"MIN. OAW BR CS All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included MAXIMUM LOAD 4000 LBS. Shown with Optional 2-Strand Drag Chain. See DC-60 or DCEZ-60 for Drag Chain Specifications. OAL OAW BR CS WEIGHT Available in 44” 48” 52” 56” 60” Only 44 1/4” 41” 37 3/4” 1990 46 1/4” 43” 39 3/4” 2108 48 1/4” 45” 41 3/4” 2226 50 1/4” 47” 43 3/4” 2344 52 1/4” 49” 45 3/4” 2462 54 1/4” 51” 47 3/4” 2580 56 1/4” 53” 49 3/4” 2690 58 1/4” 55” 51 3/4” 2816 60 1/4” 57” 53 3/4” 2934 62 1/4” 59” 55 3/4” 3052 64 1/4” 61” 57 3/4” 3170 66 1/4” 63” 59 3/4” 3288 68 1/4” 65” 61 3/4” 3406 70 1/4” 67” 63 3/4” 3524 OAW CONVEYING SURFACE DIM“A” 41” 33 3/4” 51” 44” 36 3/4” 54” 47” 39 3/4” 57” 50” 42 3/4” 60” 53” 45 3/4” 63” 56” 48 3/4” 66” 59” 51 3/4” 69” 62” 54 3/4” 72” 65” 57 3/4” 75” 68” 60 3/4” 78” 71” 63 3/4” 81” 74” 66 3/4” 84” EFFECTIVE OAL STRAND CENTERS 42” 18” 48” 24” 54” 30” 60” 36” 66” 42” 72” 48” SYSTEMS ACCESSORIES

RkJQdWJsaXNoZXIy NjQ0OTEy