Hytrol Catalog

CATALOG | 08312018 “Y” SWITCH Y Switch provides simple method of diverting or converging products from one line to another. Normal flow is to left curve looking from handle end. Transfer mechanism is raised to transfer products to other curve. Unit mounts on three stationary supports. Furnished with manual or pneumatic controls. Guard rails can be supplied–optional. • 4 Widths • Hand or Air Operated • 45˚ and 90˚ Curves Available SPUR CURVE SWITCH • 4 Widths • Hand or Air Operated • 45° and 90° curves available • Right and Left Hand Units • Hand or Air Operated TC-250 TRAFFIC COP The Traffic Cop controls product flow from one conveyor onto another. It allows products from one line of traffic to flow freely, without interference from another converging line of traffic. This eliminates collision of products which may cause damage and disrupt product flow. • 7 ArmWidths, Aluminum • Adjustable for 180˚, 90˚, 60˚, 45˚, & 30˚ Applications, specify • Locked Arm Impact Capacity is 70 lbs. at 65 FPM • 5 lbs. minimum Package Weight at 65 FPM Required to Actuate Arm • 250 lbs. maximum Accumulated Capacity WIDTH 15-1/2" STRAIGHT SECTION ON 45˚ CURVE ONLY MANUAL SWITCH LEVER 45˚ 90˚ "R" WIDTH 5'-0" "R" 15-1/2" STRAIGHT SECTION ON 45˚ CURVE ONLY 90˚ 45˚ MANUAL SWITCH LEVER RIGHT LEFT 90˚ 45˚ "R" 5'-0" WIDTH "OAW" MOUNTING ANGLE 90˚ TURNING WHEEL "A" PRODUCT FLOW PRODUCT FLOW Spur Curve Switch provides simple method of diverting or converging products from one line to another. Normal flow is through curve. Transfer mechanism is raised to transfer straight through. Unit mounts on three stationary supports. Furnished with manual or pneumatic controls. Guard rails can be supplied–optional. SYSTEMS ACCESSORIES "R" Width Degre Model No. Weight (lbs) "R" Width Degre Model No. Weight (lbs) Conveyor Width Overall Arm Length Size "A" Model No. Weight (lbs) 12" 12" TC-250-12 47 15" 15" TC-250-15 18" 18" TC-250-18 22" 22" TC-250-22 50 24" 24" TC-250-24 26" 26" TC-250-26 30"-36" 30" TC-250-30 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. 4'-0" 12" 45° 90° SYS-12-45 SYS-12-90 106 142 15" 45° 90° SYS-15-45 SYS-15-90 120 156 18" 45° 90° SYS-18-45 SYS-18-90 131 169 5'-0" 24" 45° 90° SYS-24-45 SYS-24-90 145 185 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. 4'-0" 12" 45° 90° SCS-12-45-R or L SCS-12-90-R or L 140 157 15" 45° 90° SCS-15-45-R or L SCS-15-90-R or L 153 173 18" 45° 90° SCS-18-45-R or L SCS-18-90-R or L 166 188 5'-0" 24" 45° 90° SCS-24-45-R or L SCS-24-90-R or L 190 205 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. CATALOG | 08312018 HIGH SPEED PUSHER LIGHT DUTY PUSHER The HSP provides high speed automatic product diversion. Product may be diverted 90˚ onto another conveyor, chute, etc. Special two-valve pneumatic control system provides smoother operation at speeds up to 45 cycles per minute. Cycle time varies with weight of product and stroke. WIDTH RAM FACE CUSHIONED PAD STROKE LENGTH 7/8" COVER "A" *MOUNTING ANGLE *SPACER FILTER, REGULATOR (FR) MS SUPPORT 4-1/8" 12-7/8" 9/16" 14-3/16" 4-1/8" Specify conveyor model, overall width and elevation for proper mounting kit. CAPACITY –75 lbs. maximum package weight. CYCLES –Up to 45 times per minute. Cycle rate varies with package weight. STROKE LENGTH –Available in 14 in. to 18 in., 18 in. to 24 in., or 24 in. to 30 in. ranges. May be adjusted for any length within each range. RAM FACE –12 in., 18 in., or 24 in. wide, with 1 in. thick cushioned pad. ELECTRICAL REQUIREMENTS –120 VAC power supply, 120 VAC Pulse actuation signal. NOTE : 24 Volt DC solenoids and switches available. FILTER, REGULATOR, LUBRICATOR (FRL)–Filter , dual regulator, lubricator with safety shut-off valve, 3/8 in. NPT inlet port. AIR CYLINDER –1 1/2 in. bore double acting. AIR VALVES –Double solenoid and single solenoid 4-way valves. AIR REQUIREMENTS –40 to 80 P.S.I.. Free air consumption at 60 P.S.I. -.190 cu. ft. per cycle for 14 in. to 18 in. stroke, .247 cu. ft. per cycle for 18 in. to 24 in. stroke, .304 cu. ft. per cycle for 24 in. to 30 in. stroke. NOTE : Include safety factor when calculating compressor size. STROKE LENGTH "A" 14”TO 18” 45" 18”TO 24” 51" 24”TO 30” 57" • 7”, 10”, or 15”Stroke (Specify) • Aluminum Pusher Face • 15 lb. Maximum Carton Weight • Mounting Hardware (Specify Conveyor Model & Overall Width) • Less Electrical Controls Required To Actuate Pusher Hytrol’s LD Pusher is a light duty pusher designed to easily mount to the side on many conveyor models. The LD Pusher provides an economical solution for pushing lightweight products off at a right angle to product flow. Ideally used for reject or inspection stations. The LD Pusher is not designed for high cycle applications. • STANDARD SPECIFICATIONS SYSTEMS ACCESSORIES OVERHEAD PUSH-OFF CAPACITY –150 lbs. maximum package weight. PACKAGE HEIGHT –Min. 4 1/2 in. (20 in. stroke), 6 in. (30 in. stroke)–max. 24 in. CYCLES –Up to 20 times per minute. PUSHER STROKE –20 in. or 30 in. PUSHER FACE –18 in. long 1.9 in. dia. roller. ELECTRICAL CONTROLS –Not furnished as standard equipment. AIR CYLINDER –2 in. bore double acting. AIR VALVE –Double solenoid 4-way valve, 1/4 in.–20 NPT valve ports. Electrical requirements 120V–1 Ph. 60 Hz., current draw is .09 amps. AIR REQUIREMENTS –Min. pressure 60 P.S.I., max. 125 P.S.I. free air consumption at 60 P.S.I.–.105 cu. ft. per cycle for 20 in. stroke, .176 cu. ft. for 30 in. stroke. NOTE : To eliminate contaminants in air supply line, a filter-regulator should be installed prior to the air valve (not supplied as standard). The Overhead Push-Off provides high speed automatic product diversion. Product may be diverted 90˚ onto another conveyor, chute, etc. or changed from one lane to another in parallel lines. Overhead design conserves space next to conveyor. • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy