Hytrol Catalog

CATALOG | 08312018 PSB Plastic Belt Conveyor The Model PSB with modular plastic belting uses a positive drive system to eliminate belt slippage and mistracking. • 16 Belt Widths • Polypropylene 2”Pitch Plastic Belt • Adjustable MS-Type Floor Supports Available OVERALL LENGTH "A" TOTALLY ENCLOSED CHAIN GUARD PLASTIC BELT SNUB ROLLER UHMW WEARSTRIP OPTIONAL MS SUPPORT SHOWN 2" 2" 16" 13-1/4" MAX. ALLOW 16" 11-15/16" MAX. 29-1/4" 7-1/2" 20 TOOTH, 6.4" PITCH DIA. PLASTIC SPROCKETS FLOW UHMW WEARSTRIPS TOTALLY ENCLOSED CHAIN GUARD 10 TOOTH, 6.4" PITCH DIA. OVERALL FRAME WIDTH BETWEEN RAIL WIDTH BELT WIDTH (NOMINAL) 1-1/2" 7-3/4"7-1/2" 313/16" FRAME SPACER PLASTIC BELT • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BED –Stainless steel in lieu of powder painted HRS (Excluding Aluminum Support Bars). BELT –Other belts available, contact factory. BELT SPEED –Other constant and variable speeds. V-belt drive supplied on speeds under 15 FPM and with variable speeds. Note : Capacity affected with speed change. V-BELT DRIVE –V-belt supplied between motor and reducer. Allow 65 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). CEILING HANGARS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. NOSEOVER AND NOSEUNDER –Can be incorporated to provide continuous belt travel from horizontal to incline or decline. MOTORS –Energy efficient, single phase, brakemotor, other haracteristics. 2 HP maximum. ELECTRICAL CONTROLS –One direction magnetic starters and push-button stations. AC Variable Frequency Drive. END DRIVE –Located on discharge end of conveyor. Chain guard located on left hand side. BELT –Polypropylene 2 in. pitch Flush Grid, nominal 1 in. less than BR. BED –UHMW on aluminum slider bars, mounted to frame spacers. Mounted in 7 1/2 in. x 12 ga. powder painted, formed steel channel frame bolted together with butt couplings. CROSS BRACING –Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure tracking. (1) supplied in first 50' of bed section lengths and (1) per 50' of bed section length thereafter. Supplied in approximate center of lengths. DRIVE AND TAIL SPROCKETS –10 tooth 6.4 in. pitch dia. molded plastic sprockets on 1 1/2 in. sq. shaft, 1 3/16 in. dia. shaft at bearings. SNUB ROLLERS –Located at drive and tail ends. RETURN BARS –UHMW on aluminum. BEARINGS –Sealed, pre-lubricated, self-aligning ball bearings on drive and tail shafts. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive sprocket. MOTOR –1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 200 lbs. NOT TO EXCEED capacity in chart. • STANDARD SPECIFICATIONS SECTION X-X Conveyor shown with optional floor supports SIZE TO ORDER Overall Length Belt Width 8" 10" 12" 14" 16" 18" 20" 22" 24" 26" 28" 30" 32" 34" 36" 38" Between Rail Width 9" 11" 13" 15" 17" 19" 21" 23" 25" 27" 29" 31" 33" 35" 37" 39" Overall Frame Width 12" 14" 16" 18" 20" 22" 24" 26" 28" 30" 32" 34" 36" 38" 40" 42" 10' Weights 328 248 368 388 408 428 448 468 488 508 528 548 568 588 608 628 Weights Per Foot 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 LOAD CAPACITY CHART @ 65 FPM HP 16”TO 28”OVERALLWIDTH TOTAL LOAD (LBS.) UP TO 50’ 1/2 750 1 1750 2 3750

RkJQdWJsaXNoZXIy NjQ0OTEy