Hytrol Catalog

CATALOG | 08312018 PC Portable Parts Conveyor The Model PC can be used as a portable or permanent parts conveyor. Side guards and cleated belt easily catch small stampings, plastic parts, etc., and carry them to hoppers or drums. Flapper guard prevents parts from falling through conveyor. • 8 Belt Widths • Tough Cleated Belt • Portable or Permanent • Overhead Drive • Formed Edge Guard Rails SECTION X-X SQUARE EDGE GUARD RAIL BELT CLEAT BED WIDTH BELT WIDTH 3-1/2" 10-1/8" 6-5/8" BELT RETURN 4" DIA. DRIVE PULLEY 4" DIA. WHEEL ALLOW 16" NIP POINT GUARD TAKE-UP "X" "X" OVERALL LENGTH "A" BED LENGTH "L" ADJUSTABLE TAIL SUPPORT BASE LENGTH 4" DIA. TAIL PULLEY "C" 19" 10" *"E" "H" 11" 12-5/16" MAX. ADJUSTABLE ADJUSTABLE SIZE TO ORDER Overall Length "A" Belt Width 4" 6" 8" 10" 12" 16" 18" 24" BedWidth 8" 10" 12" 14" 16" 20" 22" 28" 5' Weights (Lbs.) 348 416 420 473 477 530 583 635 7' 379 447 451 504 508 563 620 675 9' 410 478 482 535 539 596 657 714 11' 441 509 513 566 570 629 694 753 13' 472 540 544 597 601 662 731 792 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. ADJUSTMENT CHART FOR 5' TO 13' LONG UNITS Overall Length "A" Bed Length "L" Base Length Minimum Tail Minimum Tail Maximum Tail Maximum Tail Minimum Drive Maximum Drive Minimum Drive Maximum Drive "C" "H" "C" "H" "C" "H" "C" "H" *"E" 5' 4' 22" 11" 41 1/2" 10" 56" 25 1/2 37 1/2" 26" 54 1/2" 11" 7' 6' 34" 51 1/2" 76 1/2" 44 1/2" 44 1/2" 45" 73 1/2" 9' 8' 46" 64 1/2" 97 1/2" 57 1/2" 57 1/2" 48" 95 1/2" 11' 10' 58" 74 1/2" 118" 67 1/2" 67 1/2" 55 1/2" 116" 13' 12' 58" 86 1/2" 124" 67 1/2" 67 1/2" 55 1/2" 124" 35" *APPLIES TO PORTABLE BASE ONLY CATALOG | 08312018 PC BELT –2- ply black Nitrile with 1 1/2 in. high molded cleats on 12 in. centers. Clipper lacing. BED –6 5/8 in. deep x 12 ga powder painted formed steel slider bed. 3 1/2 in. high vertical sides with square edge guard rail. Standard sections are 4 ft., 6 ft., 8 ft., 10 ft., and 12 ft. long. Longer bed sections are bolted together with splice plates and joint support angles. PORTABLE BASE SUPPORT –Tubular steel support mounted on 4 in. dia. steel wheels. Adjustable to control conveyor height at top and bottom. Adjustment height can be locked in place with lever. NOTE : Not available on units longer than 13 ft. OVERHEAD END DRIVE –Motor reducer unit mounted 9 1/2 in. above belt (chain guard RH side). DRIVE PULLEY –4 in. dia. with 1 in. dia. shaft at bearings, machine crowned and fully lagged. BELT RETURN –4 in. dia. with 1 in. dia. shaft at bearings, machine crowned. TAKE-UP –Take-ups provided at tail pulley. Provides 4 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys. SPEED REDUCTION –Sealed worm gear“C”face speed reducer. No. 50 roller chain to drive pulley. MOTOR –1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –300 lbs. total distributed load at 65 FPM. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-3 support. BELT –1/2 in. x 1 in. galvanized flat wire mesh belt with 1 1/4 in. high steel angle cleats, spaced every 12 in. Galvanized low carbon steel or stainless steel. 1 in. x 1 in. or 1/2 in. x 1/2 in. mesh available. BELT SPEED –Other constant and variable speeds. V-belt drive supplied under 17 FPM. NOTE: Capacity affected with speed change. OVERHEAD END DRIVE –Higher than standard clearance above belt, specify. UNDERSIDE END DRIVE –Motor reducer unit mounted underneath bed. Extends down 11 in. from bottom of bed. PULLEYS –6 in. tail with 1 3/16 in. dia. shaft at bearings or 8 in. drive with 1 3/16 in. dia. shaft at bearings. V-BELT DRIVE –V-belt supplied between motor and reducer. Minimum overall drive width 14 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). HIGHER SIDE GUARDS –6 in., 9 in., or 12 in. high vertical sides in place of standard 3 1/2 in. high. NOTE: 12 in. high sides require higher than standard overhead or underside drive. LOWER POWERED FEEDER –Chain type driven from tail pulley of conveyor. Black friction surface belt. Includes MS-6 support. NOTE : conveyor tail pulley is used for belt take-up. When belt tension is adjusted, feeder will have to be moved along with the take-up. NOTE: Capacity affected with this option. MOTORS –Energy efficient, single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –One direction manual start switch. Non-reversing magnetic starters. Push button stations. AC variable frequency drive. • STANDARD SPECIFICATIONS FEEDER SHOWN WITH STANDARD PC TYPE GUARD RAIL, GRAVITY BRACKET WITH POP-OUT ROLLER AND OPTIONAL MS TYPE FLOOR SUPPORTS

RkJQdWJsaXNoZXIy NjQ0OTEy