Hytrol Catalog

CATALOG | 08312018 GAPPER-L The model Gapper is designed for feeding sawtooth merges, combiners, sorters, or other equipment where gaps must be optimized between cartons or for feeding scales where carton pitch must be controlled. • 5 Belt Widths • High Grip Longitudinally Grooved Belt • Pop-Out Roller • Adjustable MS-Type Floor Supports Available • 6 Speed Gap Ratios SIZE TO ORDER Overall Length Belt Width 12" 18" 24" 30" 36" Between Rail Width 15" 21" 27" 33" 39" Overall FrameWidth 18" 24" 30" 36" 42" 12' Weights 905 1059 1208 1360 1512 Weight Per Foot 21 28 35 42 47 NOTE : • 12’-0”OAL Minimum with 12”, 18”& 24”Belts • 12’-6”OAL Minimum with 30”Belt • 15’-0”OAL Minimum with 36”Belt 6' 6' 33" 33" 39" 39" 6-7/8" 19-5/16" 3/8" 1-1/2" 4-1/8" BELTWIDTH BETWEEN RAILWIDTH OVERALL FRAMEWIDTH 4-1/8" BOLT IN SLIDER PAN 6-1/2" CHANNEL TOTALLY ENCLOSED CHAIN GUARD 2-1/8" DIA. SNUB IDLER/ 1.9" RETURN IDLER "X" "X" 12' FLOW 5" OPTIONAL MS SUPPORTS SHOWN POP-OUT ROLLER OPTIONAL ROUND END 3/8" 1-1/2" 4-1/8" BELT WIDTH BETWEEN RAIL WIDTH OVERALL FRAMEWIDTH 4-1/8" BOLT IN SLIDER PAN 6-1/2" CHANNEL TOTALLY ENCLOSED CHAIN GUARD 2-1/8" DIA. SNUB IDLER/ 1.9" RETURN IDLER 12' 7' 5' 33" 33" 27" 51" 6-7/8" 19-5/16" 3/8" 1-1/2" 4-1/8" BELT WIDTH BETWEEN RAIL WIDTH OVERALL FRAME WIDTH 4-1/8" BOLT IN SLIDER PAN 6-1/2" CHANNEL TOTALLY ENCLOSED CHAIN GUARD 2- /8" DIA. SNUB IDLER/ 1.9" RETURN IDLER "X" "X" 12' FLOW OPTIONAL MS SUPPORTS SHOWN POP-OUT ROLLER 1-3/4" 44" SECTION “X-X” Conveyor shown with optional floor supports Horizontal Belt Gapping Conveyor With Controls (Slider Bed) CATALOG | 08312018 BELT –High grip longitudinally grooved belt; NSL10ELBV-UX-1-SP lacing. BED –12 ga. galvanized slider pan mounted in 6 1/2 in. x 12 ga. powder painted formed steel channel frame. CENTER DRIVE –Provides 16 in. of belt take-up. Minimum elevation–20 in. Chain guard located on left hand side. DRIVE PULLEY –8 in. dia. with 1 11/16 in. dia. shaft at bearings, machine crowned and fully lagged. TAIL PULLEY –2 1/4 in. dia. with 3/4 in. dia. shaft at bearings, machine crowned. POP OUT ROLLER –1 3/8”with high speed bearing on discharge only. SNUB IDLER –Adjustable 2 1/8 in. dia. pre-lubricated ball bearings. BEARINGS –Sealed, pre-lubricated, ball bearings on drive and tail shafts. TIMING BELT DRIVE MOTOR –5 HP Gearmotor with encoder. Requires 460 V 3 Ph. 60 Hz power supply to control panel. GAPLOGIX CONTROLS PACKAGE –Electrical control package, 460 V 3 Ph. complete with electrical enclosure, disconnect, photo eyes, variable speed drive, machine interface and software for controlling speed in order to set gaps or pitch of cartons. Contact factory for other voltages. FLOOR SUPPORTS –Now supplied as optional equipment. GAPPER-L FLOOR SUPPORT S–MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. GUARD RAILS –Adjustable Universal Channel Guard Rail, overlapping fixed channel (one direction). ROUND END – For feeding combiners, or other equipment where the pulley needs to extend past the frame. Allow 5”extension. LENGTH –Optional Lengths available in 3” increments. Minimum discharge 7’, Minimum infeed 4’, Maximum discharge 12’9”, Maximum infeed 12’9”. • OPTIONAL EQUIPMENT SGR 1.25 1.50 1.75 2.00 2.25 2.50 NOTE : As cartons pass from the infeed belt to the higher speed discharge belt, a gap is created between cartons according to the following formula: FORUMLA Length of Box + Final Gap --------------------------- = Speed Gap Ratio (SGR) Length of Box + Initial Gap Gaps are then measured and speed altered during release of cartons to create desired final gap or pitch. Discharge Belt Speed SGR = ------------------------------- Infeed Belt Speed LENGTH OF BOX INITIAL GAP FINAL GAP FLOW Discharge Belt Speed Conveyor OAW 18 24 30 36 42 HP 65 - 600 5 5 5 5 5 NOTE : Maximum operational speed will be limited to carton sizes being conveyed in order to prevent carton tumbling or sliding. Contact Factory for specific application limits. Discharge Belt Speed Infeed Belt Speed = ------------------------- SGR • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy