Hytrol Catalog

CATALOG | 08312018 Horizontal Belt Gapping Conveyor (Slider Bed) GAPPER The model Gapper is designed for feeding sawtooth merges, combiners, sorters, or other equipment where gaps must be pulled between cartons. • 5 Belt Widths • High Grip Longitudinally Grooved Belt • Pop-Out Roller • Adjustable MS-Type Floor Supports Available • 6 Speed Gap Ratios SIZE TO ORDER Overall Length Belt Width 12" 18" 24" 30" 36" Between Rail Width 15" 21" 27" 33" 39" Overall FrameWidth 18" 24" 30" 36" 42" 12' Weights 905 1059 1208 1360 1512 Weight Per Foot 21 28 35 42 47 NOTE : • 12’-0”OAL Minimum with 12”, 18”& 24”Belts • 12’-6”OAL Minimum with 30”Belt • 15’-0”OAL Minimum with 36”Belt 6' 6' 33" 33" 39" 39" 6-7/8" 19-5/16" 3/8" 1-1/2" 4-1/8" BELTWIDTH BETWEEN RAILWIDTH OVERALL FRAMEWIDTH 4-1/8" BOLT IN SLIDER PAN 6-1/2" CHANNEL TOTALLY ENCLOSED CHAIN GUARD 2-1/8" DIA. SNUB IDLER/ 1.9" RETURN IDLER "X" "X" 12' FLOW 5" OPTIONAL MS SUPPORTS SHOWN POP-OUT ROLLER OPTIONAL ROUND END 3/8" 1-1/2" 4-1/8" BELT WIDTH BETWEEN RAIL WIDTH OVERALL FRAMEWIDTH 4-1/8" BOLT IN SLIDER PAN 6-1/2" CHANNEL TOTALLY ENCLOSED CHAIN GUARD 2-1/8" DIA. SNUB IDLER/ 1.9" RETURN IDLER 12' 6' 6' 33" 33" 39" 39" 6-7/8" 19-5/16" 3/8" 1-1/2" 4-1/8" BELT WIDTH BETWEEN RAIL WIDTH OVERALL FRAMEWIDTH 4-1/8" BOLT IN SLIDER PAN 6-1/2" CHANNEL TOTALLY ENCLOSED CHAIN GUARD 2-1/8" DIA. SNUB IDLER/ 1.9" RETURN IDLER "X" "X" 12' FLOW OPTIONAL MS SUPPORTS SHOWN POP-OUT ROLLER SECTION “X-X” Conveyor shown with optional floor supports CATALOG | 08312018 BELT –High grip longitudinally grooved belt; NSL10ELBV-UX-1-SP lacing. BED –12 ga. galvanized slider pan mounted in 6 1/2 in. x 12 ga. powder painted formed steel channel frame. CENTER DRIVE –Provides 16 in. of belt take-up. Minimum elevation–20 in. Chain guard located on left hand side. DRIVE PULLEY –8 in. dia. with 1 11/16 in. dia. shaft at bearings, machine crowned and fully lagged. TAIL PULLEY –2 1/4 in. dia. with 3/4 in. dia. shaft at bearings, machine crowned. POP OUT ROLLER –1 3/8”with high speed bearing on discharge only. SNUB IDLER –Adjustable 2 1/2 in. dia. pre-lubricated ball bearings. Discharge Belt Speed Conveyor OAW 18 24 30 36 42 HP 65 1 1 1 1 1 100 1 1 1 1 1 150 1 1 1 1 1 200 2 2 2 2 2 250 2 2 2 2 2 300 2 2 2 2 2 350 2 2 2 3 3 400 3 3 3 3 3 450 3 3 3 3 3 500 3 3 3 3 5 550 3 3 3 5 5 RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated ball bearings. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail shafts. Pre- lubricated ball bearings in tread rollers. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 60 roller chain to drive pulley. MOTOR – See Chart –208/230/460/575V–3 Ph.–60 Hz. Premium Energy Efficient C-Face. FLOOR SUPPORTS –Now supplied as optional equipment. NOTE : As cartons pass from the infeed belt to the higher speed discharge belt, a gap is created between cartons according to the following formula: FORMULA Length of Box + Final Gap ------------------------------ = Speed Gap Ratio (SGR) Length of Box + Initial Gap Discharge Belt Speed Infeed Belt Speed = ---------------------- SGR GAPPER FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. GUARD RAILS –Adjustable Universal Channel Guard Rail, overlapping fixed channel (one direction). ROUND END – For feeding combiners, or other equipment where the pulley needs to extend past the frame. Allow 5”extension. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). MOTORS –Single phase, brakemotor, other characteristics. 3 HP maximum. CASTERS –See Accessory section. ELECTRICAL CONTROLS –One direction manual start switch, non-reversing starters, push button stations, encoders. AC variable frequency drive. LENGTH –Optional Lengths available in 3” increments. Minimum discharge 6’, Minimum infeed 4’, Maximum discharge 12’9”, Maximum infeed 12’9”. Horsepower will be affected. • OPTIONAL EQUIPMENT SGR 1.25 1.50 1.75 2.00 2.25 2.50 LENGTH OF BOX INITIAL GAP FINAL GAP FLOW • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy