Hytrol Catalog

CATALOG | 08312018 CATALOG | 08312018 CRB Horizontal Belt Conveyor (Troughed Roller Bed) The Model CRB is ideally used in scrap handling and recycling operations. The roller bed with deep troughed construction can carry culled or broken glass, cans, wood chips, aluminum, steel and plastic stampings. The CRB is widely used in recycling operations as an “Environmental Conveyor.” • 7 BedWidths • Side Mounted End Drive for Low Elevations • Self-cleaning Tail Pulley • Troughed Guard Rails • Adjustable MS-Type Floor Supports Available 8" DIA. DRIVE PULLEY 9-1/4" 11-1/4" 34" 47-15/16" 13-15/16" MAX. ALLOW 16" "X" "X" 2-1/8" DIA. SNUB IDLER "Y" "Y" 5" OVERALL LENGTH "A" BED LENGTH "L" SCREW TAKE-UP 6" DIA. TAIL PULLEY (SELF CLEANING) 7" 17" BELT SCRAPER OPTIONAL MS SUPPORT SHOWN OPTIONAL MS-D SUPPORT SHOWN 1.9" DIA. RETURN IDLER R.H. SIDE L.H. SIDE 9-1/4" TOP OF BELT 4-1/8" 7/8" 2" DIA. TREAD ROLLE 8-1/2" OVERALL FRAME WIDTH 11" 12" 17-1/2" TOTALLY ENCLOSED CHAIN GUARD 10-1/4" "B" "W" BETWEEN RAIL WIDTH 6" 6-1/2" 3-1/4" 15-3/4" 1/4" OVERALL FRAME WIDTH BELT WIDTH 1.9" DIA. RETURN IDLER SECTION "X-X" SECTION "Y-Y" FLOW SIZE TO ORDER Overall Length "A" Bed Length "L" Between Rail Width 9" 11" 13" 15" 17" 21" 27" Belt Width 12" 14" 16" 18" 20" 24" 30" Overall FrameWidth 16" 18" 20" 22" 24" 28" 34" "W" 17 1/2" 19 1/2" 21 1/2" 23 1/2" 25 1/2" 29 1/2" 35 1/2" "B" 28 1/2" 30 1/2" 32 1/2" 34 1/2" 36 1/2" 40 1/2" 46 1/2" 7' 5' WEIGHTS (Lbs.) Weights Based on 6" Roller Centers 410 425 440 460 480 520 570 12' 10' 525 550 570 605 635 685 765 17' 15' 675 705 735 780 825 885 990 22' 20' 790 830 865 920 975 1050 1180 27' 25' 945 990 1035 1105 1170 1260 1415 32' 30' 1055 1105 1155 1235 1315 1420 1600 42' 40' 1320 1385 1445 1550 1655 1785 2020 52' 50' 1585 1665 1740 1870 1995 2150 2440 62' 60' 1845 1940 2030 2185 2335 2520 2880 72' 70' 2110 2215 2320 2495 2670 2885 3280 82' 80' 2375 2495 2615 2815 3015 3255 3705 92' 90' 2645 2680 2715 3040 3365 3635 4135 102' 100' 2905 3050 3195 3445 3690 3985 4540 For 12" Centers Deduct Weights Listed Below Roller 5' Long Bed Sections 10' Long Bed Sections Centers BRWidth 9" 11" 13" 15" 17" 21" 27" 9" 11" 13" 15" 17" 21" 27" 12" Weight 10 12 14 16 17 21 26 20 24 28 32 34 42 52 Deduction Conveyor shown with optional floor supports CRB BELT –Black Trackmate 533 COS. Clipper lacing. BED –Roller bed with 2 in. dia. x 12 ga. unplated tread rollers spaced every 6 in., or 12 in. mounted in 10 ga. painted formed steel channel frame with 12 ga. painted side guards extending 8 1/2”above belt. Sections bolt together with splice plates. END DRIVE –Located on discharge end of conveyor, chain guard on left hand side. BELT SCRAPER –Mounted in bed section to clean underside of return belt. DRIVE PULLEY –8 in. dia. with 1 3/16 in. dia. shaft at bearings–machine crowned and fully lagged. TAIL PULLEY –6 in. dia. with 1 3/16 in. dia. shaft at bearings–self-cleaning, crowned SNUB IDLER –Adjustable–2 1/8in. dia. Pre-lubricated ball bearings. RETURN IDLER –Adjustable–1.9 in. dia. Pre-lubricated ball bearings. TAKE-UP –Screw take-ups at tail pulley. Provides 4 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, cast-iron ball bearings on drive and tail pulley. Sealed, pre-lubricated ball bearings in tread rollers. SPEED REDUCTION –Sealed worm gear“C”face speed reducer. No 50 roller chain to drive pulley. MOTOR –1 HP–208/230/460/575V–3 Ph.–60 Hz.– Premium Energy Efficient C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor–25 lbs. NOT TO EXCEED capacity in chart. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. NOTE : Drive end support non-adjustable up to 16 in. elevation. BELT SPEED –Other constant and variable speeds. V-Belt drive supplied on speeds under 17 FPM. Note : Capacity affected with speed changes. CENTER DRIVE –Provides 16 in. of belt take-up. Minimum elevation 20 in. Specify location. Minimum OAL 66 in. V- BELT DRIVE –V-belt supplied between motor and reducer. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). END CAP –A formed steel end cap is bolted to inside of conveyor at tail end to keep material from falling off end of conveyor (not available with 7 in. extended guard rail.) CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Single phase, brakemotor–other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –Non-reversing magnetic starters and push-button stations. AC variable frequency drive. LOAD CAPACITY CHART HORIZONTAL CONVEYOR ROLLER BED @ 65 FPM HP TOTAL LOAD (LBS.) UP TO 52' UP TO 102' 1 400 200 2 850 700 DETAIL VIEW OF SELF-CLEANING TAIL PULLEY • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy