Hytrol Catalog

CATALOG | 08312018 A BELT –10 in. wide Black Trackmate 120 High Grip Longitudinal Groove with PVC cover. Clipper lacing. BED –12 in. wide x .080 aluminum, 6061-T6 heat treated, reinforced. DRIVE PULLEY –6 in. dia. with 3/4 in. dia. shaft at bearings. Machine crowned and fully lagged. TAIL PULLEY –4 in. dia. with 1 in. dia. shaft at bearings, machine crowned. SNUB IDLER –Adjustable 1.7 in. dia. pre-lubricated ball bearings. RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated ball bearings. TAKE-UP –Take-ups provided at tail pulley. Provides 3 1/2 in. of belt take-up. BEARINGS –Sealed, pre-lubricated ball bearings on drive and tail pulleys. SPEED REDUCTION –4-step jackshaft V-belt and No. 40 roller chain. MOTOR –1/2 HP–115/230V–1 Ph. 60 Hz. Totally Enclosed. Wired for 115 volt. ELECTRICAL CONTROLS –Reversing drum switch with power cord and plug mounted on side shown on drawing. Specify if other side desired. BELT SPEED –Constant 83 FPM. CAPACITY –200 lbs. total distributed load, 120 lbs. unit load at 65 FPM. • OPTIONAL EQUIPMENT CLEATED BELT –Two 1 1/2 in. dia. x 1/2 in. high cleats, fastened to belt by 5/16 in. elevator bolts spaced every 60 in. Requires gear reducer drive and spooled idlers. BELT SPEED –Other constant and variable speeds. Requires gear reducer drive. NOTE: Capacity affected with speed change. RUBBER WHEELS –Two 6 in. dia. x 2 in. wide with 5/8 in. dia. shaft. STAND WITH RUBBER WHEELS –6 in. dia. x 2 in. wide wheels (with locks) mounted on adjustable tubular stand, 17 in. to 36 in. top of belt. UNDERCARRIAGE –25 in. wide tubular steel frame with hydraulic adjustment mounted on support with 4 in. dia. steel swivel casters. See drawing and adjustment chart. Not available on 16 ft., 18 ft. & 20 ft. units. ROLLER CARRIAGE –25 in. wide tubular steel support with 4 in. dia. steel swivel casters. See drawing and adjustment chart. Not available on 16 ft., 18 ft. & 20 ft. units. FLOOR SUPPORTS –Adjustable steel channel with knee braces. MSAT on tail RSAD on drive. GRAVITY CONVEYOR BRACKET –1/2 in. dia. rod for connecting wheel or roller conveyor. LOWER GRAVITY FEEDER –2 ft. long x 12 in. wide (1 1/2SW-12-24) includes adjustable tubular support and gravity conveyor bracket. UPPER GRAVITY FEEDER –2 ft. long x 12 in. wide (3SW-12-16) includes adjustable tubular support and gravity conveyor bracket. LOWER POWERED FEEDER –Chain type driven from drive pulley. 2 ft. 6 in. long belt feeder section includes adjustable tubular support and gravity conveyor bracket. GUARD RAILS –Channel type, adjustable vertically and horizontally. STAIRWAY WALL BRACKETS –Hinged brackets bolt to bed section and wall. Adjustable leg to rest on floor or step. Hook to hold conveyor close to wall when not in use. TROUGHING ATTACHMENT –Flat steel supports under belt form trough for handling loose material. Hopper available. STAINLESS STEEL BED COVER –18 ga. stainless steel skin (for ice house application). SELF-CLEANING DRIVE & TAIL PULLEYS –Crowned and ribbed to prevent clogging under belt. GEAR REDUCER DRIVE –Sealed worm gear speed reducer driven by motor with V-belt. Drive is bolted to bottom of bed. Standard motor support and guard not available. Affects mounting of other options. Consult factory. REMOTE SWITCH CONTROL –Rod running length of conveyor to operate reverse drum switch from both ends. Switch regularly furnished on side shown on drawing. Specify if required on other side. MOTORS –1/2 HP maximum. • STANDARD SPECIFICATIONS REMOTE SWITCH CONTROL ROD PERMANENT FLOOR STANDS LOWER OR UPPER GRAVITY FEEDER STAND WITH RUBBER WHEELS AND LOCKS

RkJQdWJsaXNoZXIy NjQ0OTEy