Hytrol Catalog

CATALOG | 08312018 TL BELT –Ultimate 140 BBS–Nitrile. BED –6 5/8in. deep x 12 ga. formed steel slider bed powder painted. Reinforced with 3/4in. pipe which forms sockets for guard rails. Standard 5 ft. & 10 ft. long sections bolt together with splice plates. 48 in. and 51 in. bed widths are available in 5 ft. lengths only. END DRIVE –Located on discharge end of conveyor, chain guard on left hand side. DRIVE PULLEY –8 in. dia. with 1 3/16 in. dia. shaft at bearings, machine crowned and fully lagged. TAIL PULLEY –6 in. dia. with 1 3/16 in. dia. shaft at bearings, machine crowned. SNUB IDLER –Adjustable 2 1/8 in. dia. for tail end 2 1/2 in. dia. for drive end. Pre-lubricated ball bearings. Guards included. RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated ball bearings. TAKE-UP –Take-ups at tail pulley. Provides 4 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive pulley. MOTOR–1 HP –208/230/460/575V–3 Ph.–60 Hz. Premium Energy Efficient C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 100 lbs. NOT TO EXCEED capacity in charts. FLOOR SUPPORTS –Now supplied as optional equipment. FLOOR SUPPORTS –MSType floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BELT* –White Polymate 100 RMP-COS (cover one side), Black Trackmate 120 Roughtop with PVC cover, Brown Polymate Roughtop w/Nitrile cover, Black Trackmate 533 COS-PVC, Tan Glidetop, Pure Gum Rubber Roughtop. Incline units: Black Trackmate 120 High Grip Longitudinal Groove. BELT SPEED* –Other constant and variable speeds. V-belt drive supplied on speeds under 17 FPM. OVERHEAD END DRIVE –Motor-reducer unit mounted 9 1/2 in. above belt. Other clearances available, specify. (Chain guard right hand side). Minimum elevation–10 in. SIDE MOUNTED END DRIVE –Motor-reducer unit mounted left hand side of conveyor. Minimum elevation 10 in. CENTER DRIVE –Provides 16 in. of belt take-up. Minimum elevation 20 in. Specify location. Minimum OAL 66 in. LOW ELEVATION SIDE MOUNTED CENTER DRIVE –Motor-reducer unit mounted to side of conveyor. Minimum elevation 16 1/2 in. S TACKED END DRIVE –Contact factory for minimum elevations. V-BELT DRIVE –V-Belt supplied between motor and reducer. Minimum overall drive width 14 in. Allow 65 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). UNDERSIDE TAKE-UP –Provides 16 in. of belt take-up. Extends down 15 3/4 in. from top of belt. NOSEOVER* –Adjustable, single (0 ° to 15 ° ), double (0 ° to 30 ° ). LOWER POWERED FEEDER* –Chain type driven from tail pulley of inclined conveyor. Underside take-up required when end drive is used. MS-Type floor supports now supplied as optional equipment. 8 in. dia. drive recommended on conveyor when feeder exceeds 44 1/2 in. OAL–50 1/2 in. OAL with system end. BUTT COUPLINGS –Provides connection to SB, RB, LR, ACC, ACZ, ABEZ, 190-NSP, 190-NSPEZ, 20- CR, 1.9 in. & 2.0 in. gravity conveyors. Includes 1 in. dia. pop out roller. Center drive or underside take-up recommended. SYSTEM END ROLLER –12 in. long tail sections provide connection to: SB, RB, LR, ACC, ACZ, ABEZ, 190 NSP, 190-NSPEZ, 1.9 in. & 2.0 in. gravity conveyors. Includes 1.9 in. dia. pop-out transfer roller. Belt width is 6 in. less than bed width. Center drive or underside take-up required. GUARD RAILS –Adjustable Universal Channel Guard Rail, solid side guards, PC side guards with formed top.. Fixed Channel overlapping, one direction (use with systems ends only). Fixed Channel non-overlapping, reversing (use with system ends only). CASTERS –See Accessory section. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –One direction manual start switch, reverse drum switch, non-reversing and reversible magnetic starters, push button stations. AC variable frequency drive. *NOTE: Capacity affected with these options. • OPTIONAL EQUIPMENT 8" DIA. DRIVE PULLEY HORIZONTAL LIVE LOAD CAPACITY @ 65 FPM HP BELT WIDTHS TO LENGTHS UP TO 52' 102' DISTRIBUTED LOAD (LBS.) 1 24" - 30" 530 350 36" - 42" 450 250 48" - 52" 360 100 2 24" - 30" 1250 1100 36" - 42" 1200 950 48" - 52" 1100 850 • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy