Hytrol Catalog

CATALOG | 08312018 SB BELT –Ultimate 140 BBS–Nitrile. BED –12 ga. galvanized slider pan mounted in 6 1/2 in. x 12 ga. powder painted formed steel channel frame bolted together with splice plates. CENTER DRIVE –Provides 16 in. of belt take-up. Minimum elevation– 17 3/4 in. Specify location. Minimum OAL without modification-120 in. Chain guard located on left hand side. DRIVE PULLEY –8 in. dia. with 1 7/16 in. dia. shaft at bearings, fully lagged. TAIL PULLEY –4 in. dia. with 1 in. dia. shaft at bearings or 6 in. dia. with 1 3/16 in. dia. shaft at bearings, machine crowned. SNUB IDLER –Adjustable 2 1/8in. dia. pre-lubricated ball bearings. Guards included. RETURN IDLER –Adjustable 1.9 in. dia. pre-lubricated ball bearings. TAKE-UP –Take-up in center drive provides 16 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive pulley. MOTOR –1 HP–208/230/460/575V–3 Ph.–60 Hz. Premium Energy Efficient C-Face. BELT SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 100 lbs. NOT TO EXCEED capacity in charts. FLOOR SUPPORTS –Now supplied as optional equipment. FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BELT* –Black Trackmate 120 High Grip Longitudinal Groove, White Polymate 100 RMP-COS (cover one side), Black Trackmate 533 COS-PVC, Tan Glidetop. BELT SPEED* –Other constant and variable speeds. V-belt drive supplied on speeds under 17 FPM. END DRIVE –8 in. end drive mounted on end of unit. Requires underside take-up. LOW ELEVATION SIDE MOUNTED CENTER DRIVE –Motor reducer unit mounted to side of conveyor. Minimum elevation 16 1/2 in. V-BELT DRIVE –V-Belt supplied between motor and reducer. Minimum overall drive width 14 in. Allow 65 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). GUARD RAILS –Adjustable Universal Channel Guard Rail, fixed channel, type A & B angle. Fixed Channel overlapping, one direction. Fixed Channel non-overlapping, reversing. See Accessory section. PULLEYS –6 in. tail pulley with 1 3/16 in. dia. shaft at bearings in place of 4 in. when not furnished as standard. CASTERS –See Accessory section. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –One direction manual start switch, reverse drum switch, non-reversing and reversible magnetic starters, push button stations. AC variable frequency drive. * NOTE : Capacity affected with these options. • OPTIONAL EQUIPMENT 8" DIA. DRIVE PULLEY HORIZONTAL LIVE LOAD CAPACITY @ 65 FPM HP BELT WIDTHS TO LENGTHS UP TO 52' 102' DISTRIBUTED LOAD (LBS.) 1 14" 24" 36" 48" 54" 920 890 820 770 500 870 820 720 770 300 2 14" 24" 36" 48" 54" 1920 1890 1820 1770 1200 1870 1820 1730 1650 1050 • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy