Hytrol Catalog

CATALOG | 08312018 25-PVR Poly-V Belt Driven Live Roller Conveyor (Roll-to-Roll Type) The heavy design of the 25-PVR allows it to be used for conveying higher load capacities such as loaded pallets and drums. Poly-V belt driven rollers make it ideal for conveying heavier parts where little maintenance or a quieter conveyor is required. • 15 BedWidths • Shaft Mounted Drive • Reversible • Poly-V Belt Driven Rollers • Adjustable HSN-Type Floor Supports Available 3 in., 4 in., and 6 in. Roller Centers Conveying Surface 15 3/4" 17 3/4" 19 3/4" 21 3/4" 23 3/4" 27 3/4" 29 3/4" 33 3/4" 35 3/4" 39 3/4" 43 3/4" 47 3/4" 51 3/4" 57 3/4" 63 3/4" Between Rail Width 19" 21" 23" 25" 27" 31" 33" 37" 39" 43" 47" 51" 55" 61" 67" Overall FrameWidth 22 1/4" 24 1/4" 26 1/4" 28 1/4" 30 1/4" 34 1/4" 36 1/4" 40 1/4" 42 1/4" 46 1/4" 50 1/4" 54 1/4" 58 1/4" 64 1/4" 70 1/4" 3" Centers 10' Length-O.A. 862 890 918 946 974 1030 1058 1114 1142 1198 1254 1310 1366 1450 1534 Per Foot 72 75 78 81 84 90 93 99 102 108 114 120 126 135 144 4" Centers 10' Length-O.A. 722 750 778 806 834 890 918 974 1002 1058 1114 1170 1226 1310 1394 Per Foot 61 64 67 70 73 79 82 88 91 97 103 109 113 124 133 6" Centers 10' Length-O.A. 582 610 638 666 694 750 778 834 862 918 974 1030 1086 1170 1254 Per Foot 49 52 55 58 61 67 70 76 79 85 91 97 103 112 121 • All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included • Motors will slave a maximum of 40 rollers, 20 rollers per side. Conveyor shown with optional floor supports VIEW A-A SCALE 1:5 OVERALL LENGTH OVERALL LENGTH OVERALL FRAME WIDTH BETWEEN RAIL WIDTH CONVEYING SURFACE 7/8 8 4 5 2 19/32 6 1/8 1 3/4 3/8 2 19/32 Optional HSN Supports Shown Optional HSN Supports Shown CATALOG | 08312018 25-PVR BED –Roller bed with 2 1/2 in. dia. x 11 ga. unplated tread rollers spaced every 3 in., 4 in., or 6 in. roller centers only. Tread rollers mounted in 4 in. x 4 ga. powder painted formed steel channel on side opposite guard and 5 in. x 4 ga. powder painted formed steel channel on guard side. SHAFT MOUNTED DRIVE –Shaft mounted drive to the side of the bed section. POLY-V BELT –8-rib J-Profile roller to roller. GUARD –Formed steel, upper and lower guard mounted to top and bottom of channel frame to totally enclose drive belts. BEARINGS –Sealed, pre-lubricated ball bearings. MOTOR –1 HP–208/230/460/575V–3 Ph. 60 Hz. gearmotor. CONVEYING SPEED –Constant 30 FPM. CAPACITY –– Maximum load per linear foot of conveyor 300 lb. with supports on 10 ft. centers, 1000 lb. with supports on 5 ft. centers. Total load 3000 lbs. FLOOR SUPPORTS –Now supplied as optional equipment. CONVEYOR LENGTHS –Maximum 10’per drive. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –HSN Type floor supports are available with a wide range of adjustment. Specify top or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above HSN-3 support. CONVEYING SPEED –Other constant and variable speeds. NOTE : Capacity affected with speed change. GUARD RAILS –Fixed angle (2 in. high x 1/4 in. steel) guard bolts to top flange of channel opposite guard. CHANNEL END STOP –6”x 8.2 lb. structural channel end stop. TRANSFERS –Chain transfers available. See Accessory section. MOTORS –Other HP gearmotors available. ELECTRICAL CONTROLS –Non-reversing magnetic starter – push-button stations. AC variable frequency drive. • STANDARD SPECIFICATIONS GUARD REMOVED TO ILLUSTRATE ROLL TO ROLL DRIVE BELT. WARNING: DO NOT OPERATE CONVEYOR WITH GUARD REMOVED.

RkJQdWJsaXNoZXIy NjQ0OTEy