Hytrol Catalog

CATALOG | 08312018 The Model 25-PVE24EZ Accumulating conveyor uses a 24 VDC motor/reducer to drive Poly-V Belt driven tread rollers. This conveyor is designed to handle loads such as pallets, drums, containers, etc. Products may be accumulated in zones and released upon request. • EZLogic ® Accumulation System • Poly-V Belt Driven Rollers • Shaft Mounted 24VDC Drive • Adjustable HSN-Type Floor Supports Available Conveyor shown with optional floor supports 25-PVE24EZ 24 Volt DC Horizontal Power Conveyor (Zero Pressure Accumulating Type) OAW–3 in., 4 in., and 6 in. Roller Centers. Conveying Surface 27 3/4" 29 3/4" 31 3/4" 33 3/4" 35 3/4" 37 3/4" 39 3/4" 41 3/4" 43 3/4" 45 3/4" 47 3/4" 49 3/4" 51 3/4" 53 3/4" 55 3/4" 57 3/4" 59 3/4" 61 3/4" 63 3/4" Between Rail Width 31" 33" 35" 37" 39" 41" 43" 45" 47" 49" 51" 53" 55" 57" 59" 61" 63" 65" 67" Overall FrameWidth 34 1/4" 36 1/4" 38 1/4" 40 1/4" 42 1/4" 44 1/4" 46 1/4" 48 1/4" 50 1/4" 52 1/4" 54 1/4" 56 1/4" 58 1/4" 60 1/4" 62 1/4" 64 1/4" 66 1/4" 68 1/4" 70 1/4" Weight Per Foot 3" Centers 145 151 157 163 169 175 181 187 193 199 205 211 217 223 229 235 241 247 253 Weight Per Foot 4" Centers 109 114 119 124 129 134 139 144 149 154 159 164 169 174 179 184 189 194 199 Weight Per Foot 6" Centers 84 87 90 93 96 99 102 105 108 111 114 117 120 123 126 129 132 135 138 • Total Weight = (Number of Zones x 30) + (OAL xWeight per Foot) • All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included. • Motors will slave a maximum of 40 rollers, 20 rollers per side. OVERALL FRAME WIDTH BETWEEN FRAME WIDTH CONVEYING SURFACE 17/32 8 1/8 12 IOP POWERBLOCK/E24 MOTOR 40 POWER SUPPLY RETRO-REFLECTIVE ACCUMULATION CHANNEL OPTIONAL "HSN" SUPPORTS SHOWN SECTION LENGTH SECTION LENGTH SECTION LENGTH OVERALL LENGTH FLOW 24 TM e U.S. Patent Numbers 7,243,781 • 7,591,366 7,905,345 • 6,860,381 Other Patents Pending. CATALOG | 08312018 25-PVE24EZ BED –Roller bed with 2 1/2 in. dia. x 11 ga. unplated rollers spaced every 3, 4, or 6 in. Tread rollers mounted in 4 in. x 4 ga. formed channel on side opposite chain guard and 5 in. x 4 ga. formed channel on chain guard side. Bolted together with butt couplings. POLY-V BELT –J-profile, 8 rib roller to roller GUARD –Formed steel guards totally enclose drive belts. BEARINGS –Sealed, pre-lubricated ball bearings. ACCUMULATION ZONES –4 in. roller centers, 32 in. to 120 in. on 4 in. increments. 3 in. and 6 in. roller centers, 30 in. to 120 in. on 6 in. increments. Frame length changes with zone length. MOTOR –One 24 VDC motor in each zone. EZLOGIC ® ZONE CONTROLLER –Located in each zone (Retro-Reflective). NEMA 1, 2, IP 62. UL Approved. POWER SUPPLY (FOR MOTORS) —40 amp DC power supply, 28 volt fixed output. Maximum of 8 zones per power supply. 120 vac, 24 amp input. Mounted near center of conveyor. IOP —Provides 27VDC, 100 watt power for EZLogic ® accumulation system - contains slots for 4 input/output boards. Operates up to 50 zones with maximum of 25 on either side of IOP. Requires 120VAC or 230VAC single phase input. CONVEYING SPEED – Up to 30 FPM. CAPACITY –Maximum load per linear foot of conveyor 300 lbs. with supports on 10 ft. centers and 1000 lbs with supports on 5 ft. centers. Maximum unit load 2500 lbs. per zone. Zones longer than 6 ft. may require an additional floor support depending on product load. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –HSN Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above HSN-6 support. CONVEYING SPEED –Other constant and variable speeds available, contact factory. GUARD RAILS – Angle type only. EZLogic ® – See EZLogic ® Components Page. EZLOGIC ® ACCUMULATION SYSTEM Hytrol’s EZLogic ® , or“Electronic Zero-pressure Logic”Accumulation System, combines the sensing accuracy of photo-electronics with discrete electronic logic control without the use of a PLC or pneumatic logic components. The EZLogic ® Accumulation System provides many features including: Zero-Pressure Accumulation of Product Zone Stop - Function is built in. Any zone may be transformed into a workstation by connecting a dry contact switching device to the auxiliary port of the EZLogic ® Zone Controller. This feature is always used at the discharge end of the conveyor line, and may be used at any other location where a zone stop is required. Dynamic Zone Allocation – Automatically adjusts the conveyor’s zone length to accommodate the length of the product being conveyed. Improves conveyor efficiency and system flexibility. Sleep Feature – Stops tread rollers from turning when no product is present, reducing noise, reducing energy consumption and extending roller bearing life. Unloading Zone Feature - Zone On Delay –Timer delays the zone immediately upstream from a removed load, preventing it from driving for a set time. This feature is ideal where loads are routinely removed from the conveyor with a lift truck. Loading Zone Feature – Zone detects load being placed onto the conveyor with a fork truck and stops the zone from driving and automatically prevents any loads in zones upstream from entering loading area. • STANDARD SPECIFICATIONS † Note : InfeedWake-Up Eye used only on terminating infeed end of conveyor. Not used when connecting to upstream EZLogic® conveyor through power supply isolation cable. Power Supply Max Number of Zones 20 AMP 4 40 AMP 8 F L O W F L O W RH GUARD (STANDARD) LH GUARD F L O W F L O W IOP EZLOGIC® ZONE CONTROLLER 40 AMP POWER SUPPLY MOTOR CONTROLLER E24 MOTOR/POWERCUBE INFEED EYE

RkJQdWJsaXNoZXIy NjQ0OTEy