Hytrol Catalog

CATALOG | 08312018 OAW 18” THRU 22” BR 15” THRU 19” OAW 24” THRU 42” BR 21” THRU 39” 6-1/2 12-1/2 6-1/2 12-1/2 A B C B D 15/32 2-3/4 3MIN INT 18MINTAIL Reversing O-Ring Transfers are used to move products at right angles to adjacent or parallel conveyor lines. An air bag lifts the transfer mechanism while powered O-Rings transfer the product. Linear bearings are used to guide transfer as it is raised and lowered. A gearmotor is utilized to operate the reversing mechanism to reverse transfer flow. Can be used with Models 138 and 190 NSP/NSPEZ line shaft conveyors. Chain Transfers are used to move products at right angles to adjacent or parallel conveyor lines. One air cylinder lifts the transfer mechanism while powered chains transfer the product. Chains run on UHMW polyethylene wearstrips to reduce friction. Complete unit mounts in Models ABEZ, 190-ACZ or 190-LR. CAPACITY –75 lbs. maximum unit load. TRANSFER O-RING –3/8 in. dia. polyurethane o-ring. TRANSFER SPEED –Not to exceed speed of conveyor. DRIVE –Transfer is driven from 230/460/3/60, 1/2 HP shaft-mounted gearmotor. MOUNTING –Mounted in 48 in. long section of 138-NSP, 190-NSP, 138-NSPEZ, 190-NSPEZ with 3 and 4 in. roller centers. ELECTRICAL CONTROLS –Not furnished as standard equipment. PNEUMATICS –Air bag (controlled by single solenoid valve) lifts transfer. Requires maintained electrical signal of 115V–1 Ph. 60 Hz. from photo cell, proximity switch, etc. (not supplied). Transfer will stay in raised position until signal is broken. Current consumption is .09 amps holding. AIR REQUIREMENTS –Minimum pressure 60 P.S.I., maximum 100 P.S.I. with .038 cu.ft. of free air per cycle at 60 P.S.I. NOTE : To eliminate contaminants in air supply line, a filter-regulator should be installed prior to air valve (not supplied as standard). AIR BAG ACTUATOR LINEAR BEARING 1-1/2" 1-1/2" 3" 3" 4" 4" 4" 4" 4" 4" 4-1/4" 4-1/4" 6-3/4" 4" 3" 3" 3" 3" TRANSFER CL S F O N F N O S F N O S N S F E O 16” 13” 9-1/2” 1/4” 24” 21” 9-1/2” 1/4” O N F S N S F O N O S F S O N F E F S O N 21"-39" BR 13” - 19” BR and 138-NSP 12-7/8” MINIMUM ELEVATION 17-1/2” MINIMUM ELEVATION 24” 48” Note : No accumulation in transfer section. REVERSING O-RING TRANSFER (BR TYPE) CHAIN TRANSFER (CT-200) NOTE : No brakes in ABEZ zone where CT-200 is mounted. A B D C STRAND CODES STRAND QTY STRAND CENTERS A B C D E F G H J K L M N P 2 2 2 3 2 2 3 4 2 4 2 3 4 4 6 9 12 6,6 15 18 9,9 6, 6, 6 21 6, 9, 6 24 12, 12 6, 12, 6 9, 6, 9 06” 09” 12” 12” 15” 18” 18” 18” 21” 21” 24” 24” 24” 24” N/A N/A N/A 6” N/A N/A 9” 6” N/A 6” N/A 12” 6” 9” N/A N/A N/A N/A N/A N/A N/A 6” N/A 9” N/A N/A 12” 6” 18-1/2” 21-1/2” 24-1/2” 24-1/2” 27-1/2” 30-1/2” 30-1/2” 30-1/2” 33-1/2” 33-1/2” 36-1/2” 36-1/2” 36-1/2” 36-1/2” 138-NSP OAW BR 15" 13" 18" 16" 24" 22" 190-NSP OAW BR 16" 13" 18" 15" 20" 17" 22" 19" 24" 21" 26" 23" 28" 25" 30" 27" 34" 31" 36" 33" 40" 37" 42" 39" • STANDARD SPECIFICATIONS SYSTEMS ACCESSORIES

RkJQdWJsaXNoZXIy NjQ0OTEy