Hytrol Catalog

CATALOG | 08312018 25-LREZ BELT –14 in. black Ultimate 140 SD. BED –Roller bed with 2 1/2 in. dia. x 11 ga. unplated tread rollers spaced every 3 in. and 1.9 in. dia. x 16 ga. unplated pressure rollers spaced every 6 in. Mounted in 7 1/2 in. x 10 ga. powder painted formed steel channel frame. Bolted together with butt coupling. END DRIVE –Located on infeed end of conveyor. DRIVE PULLEY –8 in. dia. with 1 7/16 in. dia. shaft at bearings, machine crowned and fully lagged. TAIL PULLEY –4 in. dia. with 1 in. dia. shaft, machine crowned. SNUB IDLER –Adjustable 2 5/8 in. dia. at drive pulley, 2 1/8 in. dia. at tail pulley. Pre-lubricated ball bearings. RETURN IDLER –2 1/8 in. dia. at drive end, all others 1.9 dia. unplated. Pre-lubricated ball bearings. TAKE-UP –Take-up at tail pulley. BEARINGS –Sealed, pre-lubricated, self-aligning ball bearings on drive and tail pulley. Sealed, pre-lubricated ball bearings in tread and pressure rollers. ACCUMULATION ZONES –3 in. roller centers, 30 in. to 72 in. on 3 in. increments. 4 in. roller centers, 32 in. to 72 in. on 4 in. increments. 6 in. roller centers, 30 in. to 72 in. on 6 in. increments. Minimum length of infeed zone (drive) is 60 in. Frame length changes with zone length. TREAD ROLLER BRAKE –Friction type brake stops tread rollers to prevent coasting of product in accumulation zone. EZLogic ® ZONE CONTROLLER –Located in each zone (Retro-reflective). NEMA 1, 2, IP 62. UL Approved. IOP —Provides 27VDC, 100 watt power for EZLogic ® accumulation system - contains slots for 4 input/output boards. Requires 120VAC or 230VAC single phase input. AIR REQUIREMENTS –Recommended working pressure 40 P.S.I. Free air consumption at 40 P.S.I.– .028 cu. ft. per sensor actuation. FILTER, REGULATOR –Supplied for main air supply line. (3/8 in. NPT port). SPEED REDUCTION –Sealed Helical–Bevel C-Face gear reducer. No.60 roller chain to drive pulley. MOTOR –1 HP–208/230/460/575V–3 PH. 60 Hz. Totally Enclosed C-Face. CONVEYING SPEED –Constant 30 FPM. CAPACITY –Maximum load per linear foot of conveyor 1000 lbs. Maximum unit load 4000 lbs. Total load NOT TO EXCEED capacity in charts. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –LRAS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. CONVEYING SPEED –Other constant speeds to 50 FPM. Note : Capacity and accumulation feature affected with speed change. UNDERSIDE TAKE-UP –Provides 12 in. of belt take-up. Minimum elevation 12 in. (Required on units 40 ft. or longer.) Must be located in 4 ft. long intermediate section. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). TREAD ROLLERS –2 5/8 in. dia. x 7 ga. unplated steel, 11/16in. hex spring loaded shaft. MOTORS –Energy efficient, single phase, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –Non-reversing magnetic starter – push-button stations. AC variable frequency drive. EZLogic ® – See EZLogic ® Components Page. LOAD CAPACITY CHART (Accumulated) @ 30 FPM HP OVERALL FRAME WIDTH 42" TO 48" OVERALL FRAMEWIDTH 50" TO 64" OVERALL FRAMEWIDTH 76" TO 88" TOTAL LOAD (LBS.) TOTAL LOAD (LBS.) TOTAL LOAD (LBS.) UP TO 25' UP TO 50' UP TO 25' UP TO 50' UP TO 25' UP TO 50' 1 16500 12900 15400 10800 13700 7500 2 *20000 23000 *20000 20900 *20000 17600 *Limited to 4000# Per Accumulation Zone NOTE : Operating 25-LREZ in slug mode is not recommended NOTE : Product footprint may affect drive capacity. EZLOGIC ® ACCUMULATION SYSTEM Hytrol’s EZLogic ® , or “Electronic Zero-pressure Logic” Accumulation System, combines the sensing accuracy of photo-electronics with discrete electronic logic control without the use of a PLC or pneumatic logic components. The EZLogic ® Accumulation System provides many features including: Zero-Pressure Accumulation of Product Zone Stop function is built in. Any zone may be transformed into a workstation by connecting a dry contact switching device to the auxiliary port of the EZLogic ® Zone Controller. This feature is always used at the discharge end of the conveyor line, and may be used at any other location where a zone stop is required. Selectable Modes of Operation Singulation Mode – Product separates while traveling down the conveyor and when it is released from the conveyor - creating a zone-length gap between products. Enhanced Slug Mode w/ Jam Protection – Product does not separate when traveling down the conveyor or when it is released from the conveyor. This allows higher product throughput at any given conveyor speed. Product will not separate on the conveyor even when accumulation has been activated at the discharge end. Cascaded Slug Release – Rather than releasing all zones simultaneously, this function introduces a momentary delay in the release of each zone, from discharge upstream. Dynamic Zone Allocation – Automatically adjusts the conveyor’s zone length to accommodate the length of the product being conveyed. Improves conveyor efficiency and system flexibility. • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy