Hytrol Catalog

CATALOG | 08312018 199-CRR Chain Driven Live Roller Conveyor The Model 199-CRR is a medium-duty chain driven live roller conveyor. The roll-to-roll chain drive makes this conveyor ideal for light to medium duty pallet handling or oily conditions which are not suitable for belt driven live roller. • 11 BedWidths • Center Drive • Reversible • Chain Driven Rollers • Adjustable MSN-Type Floor Supports Available Conveyor shown with optional floor supports SECTION X-X 9-13/16" 1/4" 3-1/2" 16-15/16" 13-3/16" 4-3/4" 13/16" 2-3/4" 1-5/32" ALLOW 16" 4-3/16" 7-3/16" 14-7/16" 18" OVERALL LENGTH OVERALL FRAME WIDTH BETWEEN RAIL WIDTH CONVEYING SURFACE 1-3/4" FLOW "X" "X" OPTIONAL MSN SUPPORTS SHOWN Conveying Surface 12 1/4" 14 1/4" 16 1/4" 18 1/4" 20 1/4" 22 1/4" 24 1/4" 28 1/4" 30 1/4" 34 1/4" 36 1/4" Between Rail Width 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39" Overall FrameWidth 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42" Base Weight 655 680 705 730 755 780 805 855 880 930 955 Weight (Lbs.) Per Foot 4" Roller Centers 51 53 55 57 59 61 63 67 69 72 75 Weight (Lbs.) Per Foot 6" Roller Centers 46 47 49 51 52 54 55 59 60 63 65 CATALOG | 08312018 199-CRR BED –Roller bed with 1.9 in. x 9 ga. wall unplated tread rollers spaced every 4 in. or 6 in. mounted in 7 ga. powder painted formed steel channel frame bolted together with butt couplings. CENTER DRIVE –Mounted underneath bed section. ROLLER CHAIN –No. 40 roller-to-roller chain. MOTOR DRIVE CHAIN –No. 60 chain. CHAIN GUARD –Mounted to top of channel frame to totally enclose drive chain. BEARINGS –Sealed, pre-lubricated ball bearings on drive roller shaft. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. MOTOR –1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face. CONVEYING SPEED –Constant 35 FPM. CAPACITY –Maximum load per linear foot of conveyor 150 lbs. with supports on 10 ft. centers, 250 lbs. per ft. with supports on 5 ft. centers and 4 in. roller centers. NOT TO EXCEED capacity in charts. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MSN Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MSN-6 support. CONVEYING SPEED –Other constant and variable speeds. NOTE : Capacity affected with speed change. SHAFT MOUNTED DRIVE –Requires shaft mounted gearmotor. Minimum elevation top of rollers 6 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). ROLLERS SET LOW –Tread rollers mounted in 4 3/4 in. x 10 ga. formed steel channel frame to form 1 in. high guard rails. CHAIN CROSSOVER –Move driving chain from one side to opposite side. GUARD RAILS –Adjustable Universal Channel Guard Rail, (both sides) fixed channel (both sides) or angle (one side). See Accessory section . POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Energy efficient, single phase, brakemotor. 2 HP maximum. ELECTRICAL CONTROLS –Non-reversing magnetic starters and push-button stations. AC variable frequency drive. LOAD CAPACITY CHART @ 35 FPM & 6" ROLLER CENTERS OVERALLWIDTH 18" - 28" 30" - 42" OVERALL LENGTH 25' 50' 25' 50' SUPPORT CENTERS 5' 10' 5' 10' 5' 10' 5' 10' HP 1/2 2250 2250 1250 1250 2000 2000 1000 1000 1 5000 3750 3250 3250 5000 3750 3000 3000 2 6250 3750 7250 7250 6250 3750 7000 7000 CHAIN GUARD REMOVED TO ILLUSTRATE ROLL TO ROLL DRIVE CHAIN. WARNING: DO NOT OPERATE CONVEYOR WITH CHAIN GUARD REMOVED. • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy