Hytrol Catalog

CATALOG | 07262019 190-ACZ BELT –Ultimate 140 BBS–Nitrile. BED –Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube spaced every 3 in. and 1.9 in. dia. pressure roller x 16 ga. galvanized tube spaced every 6 in. Mounted in 6 1/2 in. x 12 ga. powder painted formed steel channel frame bolted together with butt couplings. CROSS BRACING –Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure correct product tracking. Supplied to section adjoining drive and every other section, 20 ft bed lengths and over. Supplied on bed lengths 9 ft and over. CENTER DRIVE –Can be placed in any section of conveyor length. DRIVE PULLEY –8 in. dia. with 1 7/16 in. dia. shaft at bearings, fully lagged. TAIL PULLEY –4 in. dia. with 1 in. dia. shaft at bearings,machine crowned. SNUB IDLER –Adjustable 2 1/8 in dia. pre-lubricated ball bearings. RETURN IDLER –Adjustable 1.9 in dia. pre-lubricated ball bearings. TAKE-UP –Take-ups in center drive. Provides 16 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive, tail, and take-up pulleys. Pre-lubricated ball bearings in tread and pressure rollers. SPEED REDUCTION –Sealed worm C-Face gear reducer. No. 50 roller chain to drive sheave. MOTOR –1/2 HP–208/230/460/575V–3 PH. 60 Hz. Totally Enclosed C-Face. CONVEYING SPEED –Constant 65 FPM. CAPACITY –Maximum load per linear foot of conveyor 150 lbs. NOT TO EXCEED capacity in chart. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. CONVEYING SPEED –Other constant and variable speeds from 20 to 90 FPM. V-belt drive supplied under 46 FPM (2 HP) and with variable speeds. NOTE : Capacity and accumulation feature affected with speed change. SIDE MOUNTED LOW ELEVATION CENTER DRIVE –Motor reducer unit mounted to side of conveyor. Minimum low elevation16 in. SIDE MOUNTED END DRIVE –Minimum elevation 12 1/4 in. (underside take-up required). V-BELT DRIVE –V-belt supplied between motor and reducer. Allow 65 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). PACKAGE STOPS –Roller or pin type stops available, contact factory. GUARD RAILS –Adjustable Universal Channel Guard Rail, fixed channel, type A angle elevated to allow for pop-out tread rollers. Type B angle not available. (See Accessory section.) NOTE : If product comes in contact with guard rails, product flow will be affected. Fixed channel overlapping, one direction. Fixed channel non-overlapping, reversing. ROLLER CENTERS –Tread rollers spaced every 4 in., 6 in., or 8 in. (4 in. or 8 in. centers NOT AVAILABLE in 7 ft. 6 in. bed). POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Energy efficient, single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –Non-reversing or reversible magnetic starters and push–button stations. AC variable frequency drive. LOAD CAPACITY CHART @ 65 FPM HP OVERALL FRAMEWIDTH 16" TO 22" OVERALL FRAMEWIDTH 24" TO 30" OVERALL FRAMEWIDTH 34" TO 42" TOTAL LOAD (LBS.) TOTAL LOAD (LBS.) TOTAL LOAD (LBS.) UP TO 50' UP TO 100' UP TO 50' UP TO 100' UP TO 50' UP TO 100' 1/2 1100 200 600 – – – 1 3300 2400 2800 1600 2200 – 2 7000 6000 6400 5200 5800 3300 • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy