Hytrol Catalog

CATALOG | 08312018 190-NSPEZC Live Roller Conveyor (Zero Pressure Accumulating Type) The 190-NSPEZC Curves are designed to be slave driven from the 190-NSPEZ Conveyor. Curves are used where turns in the conveyor line are necessary. • EZLogic ® Accumulation System • Singulation, Slug or Cascaded Slug Operation • Dynamic Zone Allocation • Positive Brake on All Rollers • Adjustable MS-Type Floor Supports Available 18" "U" JOINT 18" SHAFT COUPLING DRIVE SHAFT "R" "R" 30˚ "X" "X" "X" "X" "X" "X" "X" "X" SHAFT COUPLING SHAFT COUPLING 18" "R" "R" DRIVE SHAFT 45˚ 18" "U" JOINT "U" JOINT 6-1/4" 6-1/4" DRIVE SHAFT 60˚ 6-1/4" DRIVE SHAFT 90˚ SHAFT COUPLING 6-1/4" "U" JOINT 1-5/8" OVERALL FRAME WIDTH BETWEEN RAIL WIDTH 1-5/8" 1-1/2" REFLECTOR DRIVE O-RING DRIVE SPOOL DRIVE SHAFT GUARD 2" 1/4" EZLOGIC® ZONE CONTROLLER 6-1/2" 9-1/2" PNEUMATIC BRAKE SECTION “X-X” Between Rail Width Overall Frame Width "R" Total Number of Rollers* WEIGHTS (Lbs.) 90º 60º 45º 30º 90º 60º 45º 30º 13" 16" 24" 16T/4S 10T/4S 8T/12S 5T/12S 202 167 180 152 15" 18" 32 1/2" 20T/4S 12T/4S 10T/12S 6T/12S 251 210 209 173 17" 20" 264 223 218 180 19" 22" 278 236 229 187 21" 24" 290 251 238 196 23" 26" 312 260 249 204 25" 28" 317 273 258 212 27" 30" 332 285 268 222 31" 34" 48" 28T/4S 20T/4S 14T/12S 10T/12S 480 374 346 274 33" 36" 495 386 359 286 37" 40" 529 414 383 299 39" 42" 548 429 395 312 *T = TAPERED S = STRAIGHT All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. U.S. Patent Numbers 7,243,781 • 7,591,366 7,905,345 Other Patents Pending. CATALOG | 08312018 190-NSPEZC BED –Roller bed with 2 1/2 in. dia. tapered to 1 11/16 in. dia. x 14 ga. galvanized and 1.9 in. dia. roller x 16 ga. galvanized tube. Mounted in 9 1/2 in. x 12 ga. powder painted formed steel channel frame. SLAVE DRIVEN –Curves and spurs are slave driven from drive shaft of Model 190-NSPEZ conveyor. Shafts are coupled by chain coupling at bed joints. DRIVE SHAFT –1 in. dia. steel shaft extends full length of conveyor, coupled with universal joints (U joints) at necessary intervals. DRIVE SPOOLS –2 in. dia. Delrin spool held in place on drive shaft with spool spacers. DRIVE GUARD –Underside of drive shaft with spools and drive o-rings guarded full length of conveyor. DRIVE O-RING –3/16 in. dia. polyurethane o-ring from drive spool to tread roller. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings with eccentric lock collar on drive shaft. Pre-lubricated ball bearings in tread rollers. ACCUMULATION ZONES –24 in. long air controlled. 2 per curve. SPLICE ANGLE –Standard for connecting to 190-NSPEZ or 190-NSP. CAPACITY –Maximum load see capacity chart below. FLOOR SUPPORTS –Now supplied as optional equipment. FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. GUARD RAILS –Adjustable Universal Channel Guard Rail, fixed channel or type A or B angle. Note : If product comes in contact with guard rails, product flow will be affected. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. EZLogic ® – See EZLogic ® Components Page. LOAD CAPACITY CHART 190-NSPEZC Overall FrameWidth Capacity Per Curve (Lbs.) 16" 150 18" to 30" 200 34" to 42" 300 FLOW FLOW FLOW FLOW EZLogic ® Module TYPE A MODULE ON OUTSIDE OF THE CURVE STANDARD • STANDARD SPECIFICATIONS • OPTIONAL EQUIPMENT • STANDARD SPECIFICATIONS STANDARD TYPE B MODULE ON OUTSIDE OF THE CURVE OPTIONAL TYPE C MODULE ON INSIDE OF THE CURVE OPTIONAL TYPE D MODULE ON INSIDE OF THE CURVE

RkJQdWJsaXNoZXIy NjQ0OTEy