Hytrol Catalog

CATALOG | 08312018 Live Roller Conveyor 190-NSP • 12 BedWidths • Reversible • Adjustable MS-Type Floor Supports Available The Model 190-NSP Live Roller Spool Conveyor is a general transport conveyor with the capabilities of accumulating products with back pressure. Quiet operation, versatile design, easy installation and maintenance make the 190- NSP conveyor a valuable component in operations requiring high performance with minimal downtime. FLOW 2" DRIVE GUARD OPTIONAL MS SUPPORT SHOWN DRIVE SHAFT TOTALLY ENCLOSED CHAIN GUARD SECTION LENGTH 1.9" DIA. TREAD ROLLER SHAFT COUPLING OVERALL LENGTH "A" "X" "X" 13-13/16" 2" 23-9/16" 9-3/4" 12" 4-1/4" DRIVE SPOOL DRIVE O-RING 1-1/2" 1/4" 9-1/2" OVERALL FRAME WIDTH BETWEEN RAIL WIDTH DRIVE GUARD SECTION “X-X” Conveyor shown with optional floor supports SIZE TO ORDER Overall Length "A" Between Rail Width 13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39" Overall FrameWidth 16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42" 5’ WEIGHTS (Lbs.) Weights Based on 3" Roller Centers 229 236 249 259 272 284 293 307 329 341 364 376 10’ 371 384 409 426 450 472 488 514 553 576 618 639 15’ 513 533 569 594 629 660 684 721 778 811 872 902 20’ 655 682 729 761 808 848 880 928 1003 1046 1126 1166 25’ 797 830 889 929 987 1036 1076 1135 1228 1281 1380 1429 30’ 939 979 1049 1096 1166 1224 1271 1342 1453 1517 1634 1692 35’ 1082 1128 1209 1264 1344 1413 1467 1549 1678 1752 1888 1956 40’ 1224 1276 1369 1431 1523 1601 1663 1756 1903 1987 2142 2219 45’ 1366 1425 1529 1599 1702 1789 1859 1963 2127 2222 2396 2483 50’ 1508 1574 1689 1767 1881 1977 2054 2170 2352 2458 2650 2746 55’ 1650 1723 1849 1934 2060 2165 2250 2377 2577 2693 2904 3009 60’ 1793 1871 2009 2102 2239 2354 2446 2584 2802 2928 3158 3273 65’ 1935 2020 2169 2269 2417 2542 2642 2791 3027 3163 3412 3536 70’ 2077 2169 2329 2437 2596 2730 2837 2998 3252 3399 3666 3800 75’ 2219 2317 2489 2604 2775 2918 3033 3205 3477 3634 3920 4063 80’ 2361 2466 2649 2772 2954 3106 3229 3412 3702 3869 4174 4326 85’ 2503 2615 2809 2939 3133 3294 3425 3619 3926 4104 4428 4590 90’ 2646 2764 2969 3107 3311 3483 3621 3826 4151 4340 4682 4853 95’ 2788 2912 3129 3274 3490 3671 3816 4033 4376 4575 4936 5117 100’ 2930 3061 3289 3442 3669 3859 4012 4240 4601 4810 5190 5380 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. CATALOG | 08312018 • STANDARD SPECIFICATIONS 190-NSP BED –Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube spaced every 3 in. Mounted in 9 1/2 in. x 12 ga. powder painted formed steel channel frame bolted together with splice plates. CROSS BRACING –Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure tracking. (1) supplied in first 50' of bed section lengths and (1) per 50' of bed section length thereafter. Supplied in approximate center of lengths. DRIVE –Mounted underneath, placed near center of conveyor. NOTE : On Conveyors less than 24 in. OAWmotor extends beyond frame. Chain guard located on left hand side. DRIVE SHAFT –1 in. dia. steel shaft extends full length of conveyor. Chain coupling at bed joints. Located on left hand side. DRIVE SPOOLS –2 in. dia. Delrin spool held in place on drive shaft with spool spacers. DRIVE GUARD –Underside of drive shaft with spools and drive o-rings guarded full length of conveyor. DRIVE O-RING –3/16 in. dia. polyurethane o-ring from drive spool to tread rollers. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings with eccentric lock collar on drive shaft. Pre-lubricated ball bearings in tread rollers. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive shaft. MOTOR –1/2 HP–208/230/460/575V–3 Ph. 60 Hz Totally Enclosed C-Face. CONVEYING SPEED –Constant 65 FPM. CAPACITY –Maximum load per powered roller–15 lbs. NOTE : Maximum load capacity will be less for products with soft or irregular bottoms. Total load NOT TO EXCEED capacity in chart. FLOOR SUPPORTS –Now supplied as optional equipment. FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. CONVEYING SPEED –Other constant and variable speeds from 30 to 120 FPM. Over 120 FPM timing belt drive recommended. Capacity affected with speed change. SIDE MOUNTED DRIVE –with Hytrol Reducer. SIDE MOUNTED DRIVE –with Gearmotor. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). LOW ELEVATION DRIVE –Gearmotor mounted inside of conveyor. Minimum elevation 11 1/4 in. POSITIVE DRIVE –Spools are keyed to drive shaft in positive drive areas. CROSSOVER –Separatesectionrelocatesdriveshaft fromonesideofconveyortotheother. Minimum Elevation—12 3/8 in. ONE DIRECTION O-RING TRANSFER – See Conveyor Accessories. REVERSING O-RING TRANSFER – See Accessories section. GUARD RAILS –Adjustable Universal Channel Guard Rail, fixed channel or type A & B angle. Note : If product comes in contact with guard rails, product flow will be affected. Fixed channel overlapping, one direction. Fixed channel non-overlapping, reversing. PACKAGE STOPS –Blade, roller or pin type stops available, contact factory. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Energy efficient, single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –Non-reversing or reversible magnetic starters and push-button stations. AC variable frequency drive. • OPTIONAL EQUIPMENT 1) Powered drive shaft (coupled at bed joints) is bearing supported on frame. 2) Drive o-ring transmits power to tread rollers from drive shaft. 3) Drive spool (held in place by spool spacers) and groove in tread roller keep drive o-ring in position. 4) If back pressure (accumulation) is applied to tread roller, drive spool will slip on drive shaft, stopping power to tread roller. LOAD CAPACITY CHART @ 65 FPM HP OVERALL FRAMEWIDTH OVERALL FRAMEWIDTH OVERALL FRAMEWIDTH 16" to 22" 24" to 30" 34" to 42" TOTAL LOAD (Lbs.) TOTAL LOAD (Lbs.) TOTAL LOAD (Lbs.) UP TO 60' UP TO 90' UP TO 120' UP TO 60' UP TO 90' UP TO 120' UP TO 60' UP TO 90' UP TO 120' 1/2 1550 580 – 1340 250 – 1020 – – 1 *3600 4090 3110 *3600 3770 2680 *3600 3280 2040 2 – – *7200 – – *7200 – – *7200 *Limited to 15 lbs. per driven roller. NOTE : Capacity in Chart based on 3 in. roller centers with all rollers powered. MOTOR SELECTION CHART FPM 30-44 45-120 HP (MAX) 1 2 If the required horsepower exceeds the maximum horsepower shown in the chart, more than one drive is required TREAD ROLLER DRIVE O-RINGS DRIVE SHAFT DRIVE SPOOL FLOW SPOOL SPACER SHORT SPOOL SPACER

RkJQdWJsaXNoZXIy NjQ0OTEy