Hytrol Catalog

CATALOG | 08312018 190-ACC Horizontal Power Conveyor (Accumulating Type) The simplest method ever devised for accumulating cartons, boxes, etc. Basic design eliminates complicated adjustments and allows a minimum 2% back pressure. • 12 BedWidths • 2% Minimum Back Pressure • Finger Tip Snub Roller Adjustment, No Tools Needed • Reversible • Adjustable MS-Type Floor Supports Available Conveyor shown with optional floor supports 13-1/4" MAX. 16" "Y" "X" "Y" "X" RETURN TAKE-UP SHEAVE 5-3/4" DIA. DOUBLE GROOVE SHEAVE 2" OVERALL LENGTH "A" END GUARD 18-11/16" MAX. 2" ALLOW 16" 29-1/4" OPTIONAL MS SUPPORT SHOWN 12-1/8" MAX. 1” DIA. TAIL AND INTERMEDIATE SHAFT 1-1/4” DIA. DRIVE SHAFT OVERALL FRAME WIDTH BETWEEN RAIL WIDTH 1-1/2" 1/4" 6-1/2" 1.9" DIA. PRESSURE ROLLER RETURN TAKE-UP SHEAVE KNURLED NUT SUSPENSION ANGLE DRIVE V-BELT 1.9" DIA. TREAD ROLLER SECTION “X-X” 10-1/2" 3-3/4" TOTALLY ENCLOSED CHAIN GUARD 4-3/8" SECTION “Y-Y” SIZE TO ORDER Overall Length "A" Between Rail Width 13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39" Overall Frame Width 16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42" 5’ WEIGHTS (Lbs.) Weights Based on 3" Roller Centers 231 238 252 263 277 289 299 314 337 350 375 387 10’ 370 384 410 429 455 477 495 522 564 588 633 655 15’ 509 530 568 595 633 665 691 730 791 826 891 923 20’ 648 676 726 761 811 853 887 938 1018 1064 1149 1191 25’ 787 822 884 927 989 1041 1083 1146 1245 1302 1407 1459 30’ 926 968 1042 1093 1167 1229 1279 1354 1472 1540 1665 1727 35’ 1065 1114 1200 1259 1345 1417 1475 1562 1699 1778 1923 1995 40’ 1204 1260 1358 1425 1523 1605 1671 1770 1926 2016 2181 2263 45’ 1343 1406 1516 1591 1701 1793 1867 1978 2153 2254 2439 2531 50’ 1482 1552 1674 1757 1879 1981 2063 2186 2380 2492 2697 2799 55’ 1621 1698 1832 1923 2057 2169 2259 2394 2607 2730 2955 3067 60’ 1760 1844 1990 2089 2235 2357 2455 2602 2834 2968 3213 3335 65’ 1899 1990 2148 2255 2413 2545 2651 2810 3061 3206 3471 3603 70’ 2038 2136 2306 2421 2591 2733 2847 3018 3288 3444 4503 3871 75’ 2177 2282 2464 2587 2769 2921 3043 3226 3515 3682 3987 4139 80’ 2316 2428 2622 2753 2947 3109 3239 3434 3742 3920 4245 4407 85’ 2455 2574 2780 2919 3125 3297 3435 3642 3969 4158 3503 4675 90’ 2594 2720 2938 3085 3303 3485 3631 3850 4196 4396 4761 4943 95’ 2733 2886 3096 3251 3481 3673 3827 4058 4423 4634 5019 5211 100’ 2872 3012 3254 3417 3659 3861 4023 4266 4650 4872 5277 5479 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. NOTE : Stockyard drives are located on 10 ft beds only. NOTE : 16”, 20”, 22”, 26”, 28”, 34”, 36”, 40”& 42”Overall FrameWidths - 1Week Stockyard NOTE : Intermediate bed sections are available in multiples of 4 ft., 5 ft., 6 ft., 7 1/2 ft., 8 ft., and 10 ft lengths only. Conveyor shown with featured option - shaft mounted drive. FEATURED OPTION- SHAFT MOUNTED DRIVE SHOWN MOUNTED HORIZONTAL 6-3/4” 3/8” 1/4” 1-1/8” 6-1/2” 10-1/2” SPEED CHART FOR SHAFT MOUNTED DRIVE ON 190ACC SPEED FPM MAX HP MOTOR FRAME 26 1/2 56C 32 1 56C 43 1 56C 52 1 56C 64 2 140TC 86 2 140TC 103 2 140TC 129 2 140TC *172 2 140TC *257 2 140TC *343 2 140TC CATALOG | 08312018 190-ACC BED –Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube spaced every 3 in. and 1.9 in. dia. pressure rollers x 16 ga. galvanized tube spaced every 6 in. Mounted in 6 1/2 in. x 12 ga. powder painted formed steel channel frame bolted together with butt couplings. CROSS BRACING –Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure tracking. (1) supplied in first 50' of bed section lengths and (1) per 50' of bed section length thereafter. Supplied in approximate center of lengths. DRIVE –Mounted underneath, placed near center of conveyor. DRIVE BELT –Endless B-section aramid core V-Belt drives each section of conveyor. RETURN TAKE-UP SHEAVE –3 1/4 in. dia. x 1/2 bore flat idler has seven position adjustment to maintain proper V-belt tension. BEARINGS –Tread & pressure rollers have pre-lubricated ball bearings. Flange and pillow block bearings are sealed, pre-lubricated with eccentric lock collar. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive shaft. MOTOR –1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Totally Enclosed C-Face. CONVEYING SPEED –Constant 25 - 120 FPM. CAPACITY –Maximum load per linear foot of conveyor 150 lbs. NOT TO EXCEED capacity in chart. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. CONVEYING SPEED –Other constant speeds from 25 to 120 FPM.V-belt drive supplied under 56 FPM (with 1 HP). NOTE : Capacity and accumulation feature affected with speed change. SHAFT MOUNTED DRIVE – Motor reducer unit mounted on extended drive shaft. Can be mounted with standard sheave retainer for 10 1/2 in. elevation (motor horizontal), or can be mounted with low elevation sheave retainer for 8 3/4 in. elevation (motor vertical). Mounting bracket and torque arm allows for multiple mounting positions. See above chart for speeds. SIDE MOUNTED DRIVE –Motor reducer unit mounted to side of conveyor. Elevation 10 1/2 in. with standard sheave retainer. 9 3/8 in. elevation at drive, 8 3/4 in. elevation at intermediate when low elevation sheave retainer used. V-BELT DRIVE –V-belt supplied between motor and reducer. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). PACKAGE STOPS –Roller or pin type stops available. GUARD RAILS –Adjustable Universal Channel Guard Rail, fixed channel, type A & B angle. (See Accessory section.) NOTE : If product comes in contact with guard rails, product flow will be affected. Fixed channel overlapping, one direction. Fixed channel non-overlapping, reversing. ROLLER CENTERS –Tread rollers spaced every 2 in. and 4 in. (NOT AVAILABLE in 7 ft. 6 in. bed). SPRING BALANCED GATE – See 190-E24G powered or gravity die spring balanced gate. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTORS –Energy efficient, single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS –Non-reversing or reversible magnetic starters and push-button stations. AC variable frequency drive. The driving of the tread rollers on the HYTROL minimum pressure conveyor is accomplished with the top surface of a standard section endless flat belt. The strength and wear qualities of the tread rollers and this belt have been thoroughly tested for continuous duty. To maintain the driving of the tread roller, the pressure roller is mounted in spring adjusted carriers (See Photo) which sense the required driving friction regardless of the length of accumulated load. This pressure can be maintained constantly to give a 2%minimum back pressure in either a forward or reverse direction. In the event of extreme changes in unit load (weight of box or package), convenient knurled thumb adjusting nuts can be turned to accept this heavier load. This method eliminates the need for selecting proper tension spring holes in trigger mechanisms or jogging cleats on driving belt and eccentric (off center) tread rollers. By maintaining a constant minimum pressure on the tread rollers, long loads may be conveyed, accumulated or stopped on the conveyor at any point using very little motor horsepower and giving practically no pressure between boxes or packages. • HOW IT WORKS Minimum Back Pressure (2% of Total Distributed Load) Tread Roller Knurled Thumb Adjusting Nut Spring Adjusted Carrier Conveyor shown with optional floor supports LOAD CAPACITY CHART @ 65 FPM HP OVERALL FRAMEWIDTHS 16" to 22" OVERALL FRAMEWIDTHS 24" to 30" OVERALL FRAMEWIDTHS 34" to 42" TOTAL LOAD (Lbs.) UP TO 100' TOTAL LOAD (Lbs.) UP TO 100' TOTAL LOAD (Lbs.) UP TO 100' 1/2 1000 800 500 1 2400 2200 2000 2 3500 3000 2600 • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy