Hytrol Catalog

CATALOG | 08312018 Note: ProSort 122 requires that a catenary intermediate section be used with standard length drive and standard gearmotor mounting or that a minimum 51" length drive be used with a reverse mounted gearmotor. ProSort 132 requires that a catenary intermediate section be used with standard length drive and standard gearmotor mounting or that a minimum 45" length drive be used with a reverse mounted gearmotor. INTERMEDIATE –16 in. deep x 1 1/2 in. bottom flange inside, 12 ga. formed steel frame-powder painted. TAIL BED –16 in. deep x 1 1/2 in. bottom flange inside, 7 ga formed steel frame - powder painted DRIVE/CATENARY BED –30 in. deep formed steel frame-powder painted. CARRYING CHAIN –Dual strands of No. 60 prelubricated o-ring roller chain with precision bearings and extended pins. CATENARY TAKE-UP –Underside catenary take-up provided at drive end. CHAIN LUBRICATOR –Installed at infeed end to lubricate carrying chains. Gravity feed with 24 volt DC on/ off switch. Flow control valves to control the amount of oil allowed to flow to each of the brush applicators. SLATS –Anodized aluminum slats supported at each end by bushings and extended chain pins on 1 1/2 in. centers. DIVERT SHOES –Low friction molded base with high friction pusher face. Steel guide pin for switching and ball bearing cam follower for diverting. Located on 3 in. centers. SWITCH ASSEMBLY –Pneumatic operated switch assembly mounted with rubber isolators for quietness and easily removable for maintenance. AIR REQUIREMENTS –Free air consumption at 60 P.S.I. equals .002 cu. ft. per divert. AIR VALVE –High Speed 24 volt DC single solenoid 4-way air valve at each divert station. AIR FILTER, REGULATOR –Supplied for main air supply line.—1/2 in. NPT ports. Required working pressure of 60 P.S.I. AIR PRESSURE SWITCH –Install in main air line near the last divert switch. Used to detect low air pressure and turn off drive. SMART PROXIMITY SWITCHES –24 Volt DC inductive proximity switch. One at each divert. Requires maintained electrical signal for duration of each divert. SAFETY SWITCHES –Switches located at infeed and discharge ends to detect stray divert shoes or internal jams. Additional switch supplied at 30 ft. intervals. Interrupts power to drive motor when these conditions are detected. DRIVE –Shaft mounted gear motor. 230/460V- 3Ph. 60HZ. Horsepower based on speed and length requirements. See note under chart below for mounting info. VARIABLE SPEED CONTROLLER –Provides smooth acceleration of drive motor and speed variations if necessary. CONVEYING SPEED –Determined by application requirements. Up to 450 FPM on ProSort 122. Up to 350 FPM on ProSort 132. PACKAGE SIZE –Minimum 4 1/2 in. long. CAPACITY –Maximum load-25 lbs. per ft. Maximum product weight is 50 lbs. INDUCTION CONVEYOR –Belt conveyor slave driven from sorter at same speed as sorter. FLOOR SUPPORTS –Not supplied as standard. See optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –MHS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MHS-6 support. Vibration pads between channel and supports. TAKE AWAY LINES –Gravity spurs are available. Consult factory for recommendation of type and configuration. PROSORT LOGIX CONTROL PACKAGE –Provides complete controls for proper sorter operation. Contact factory for details. • STANDARD SPECIFICATIONS • STANDARD SPECIFICATIONS - INDUCTION CONVEYOR BELT –Black, high-grip, longitudal groove with high speed lacing, belt width is 6 in. less than bed width. BED –12 ga. galvanized slider pan mounted in 6 1/2 in. x 12 ga. painted formed steel channel frame. DRIVE –Slave driven at same speed as sorter via timing belt and bolted directly to infeed of sorter. Access holes designed into side plate for ease of pulley removal. DRIVE PULLEY –8 in. dia. with 1 11/16 in. dia. shaft at bearings-machine crowned. TAKE-UP PULLEY –6 in. dia. with 1 7/16 in. dia. shaft at bearings-machine crowned. TAIL PULLEY –2 1/4 in. dia.-Machine crowned and easily removable. TAKE-UP –Take-ups in drive provide 16 in. of belt take-up. BEARINGS –Sealed, pre-lubricated, self-aligning, ball bearings on drive. Sorter Conveying Surface Width Sorter Overall Width "OAW" Induction Bed Width "OAW" Spur Width "OAW" CONVEYOR SECTION Drive (not including gearmotor) Tail (not including induction belt) Divert section with 22 degree diverter ProSort 122 Divert section with 30 degree diverter ProSort 132 Intermediate with no Diverter Length Wt (LBS) Length Wt (LBS) Length Wt (LBS) Length Wt (LBS) Length Wt (LBS/FT) 15" 31" 18" 18" 42" 570 30" 322 81" 453 60" 335 9" to 120" on 3" increments 59 21" 37" 24" 24" 607 344 96" 584 69" 420 69 27" 43" 30" 30" 641 366 111" 729 81" 532 79 33" 49" 36" 36" 674 385 126" 875 90" 626 88 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. Gearmotor Wt. HP LBS 3 100 5 181 7.5 209 10 254 15 287 PROSORT 122 & 132 ELITE