Hytrol Catalog

CATALOG | 08312018 138-LRSS Live Roller Straight Spur Conveyor • 4 BedWidths • Reversible • Right or Left Hand Units Available • Adjustable LS-Type Floor Supports Available The Model 138-LRSS Live Roller Straight Spur is used in diverging or converging applications. It may be self- powered or can be slave driven from 138-ACC, LRC, or LRS conveyors. SECTION “X-X” Between Rail Width Overall Frame Width "A" "B" WEIGHTS (Lbs.) 45º 30º 45º 30º 45º 30º 10" 12" 23" 32" 21" 30" 162 187 13" 15" 26" 38" 24" 36" 167 193 16" 18" 32" 44" 30" 42" 172 200 22" 24" 41" 56" 39" 54" 177 206 All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included. "X" "X" 4" 2" (12" OAW ONLY) OAW 30˚ 45˚ 69" 49-1/32" 48-13/16" "Y" "Y" "A" "B" 59-3/4" "A" "B" 34-23/32" 2" (12" OAW ONLY) "X" "X" "Y" "Y" 69" 4" OAW 18" 2" SNUB RETURN SHEAVE ROLLER BED PRESSURE SHEAVE OPTIONAL LS SUPPORT SHOWN BELT TAKE-UP MOUNTING BRACKET 16" 13-1/4" ALLOW 16" 29-1/4" OVERALL FRAME WIDTH BETWEEN RAIL WIDTH 9-3/4" END GUARD TOTALLY ENCLOSED CHAIN GUARD 1" DRIVING V-BELT SHEAVE 1/4" 6-1/2" 11-1/4" 18" SECTION “Y-Y” CATALOG | 08312018 138-LRSS BED –Roller bed with 1 3/8 in. dia. roller x 18 ga. galvanized tube 5/16 in. HRS hex shafts spaced every 1 1/2 in. Mounted in 6 1/2 in. x 12 ga. powder painted steel frame. END DRIVE –Mounted underneath bed section. DRIVE BELT –Endless B-section aramid core V-Belt drives each section of conveyor. PRESSURE SHEAVES –2 1/2in. dia. with 3/8 in. bore. SNUB RETURN SHEAVE –3 1/4in. dia. x 1/2 in. bore flat idler has seven position adjustment. TAKE-UP –Take-up provided to maintain proper V-belt tension. Includes 4 3/8 in. dia. x 5/8 in. bore V type take-up sheave. BEARINGS –Tread rollers have pre-lubricated, self aligning ball bearings. Flange and pillow block bearings are sealed, pre-lubricated with eccentric lock collar. MOUNTING BRACKET –Bracket is supplied to attach spur to side channels of 138-ACC conveyor. BUTT COUPLINGS –Standard for connecting 138-ACC and 138-LRC. SPEED REDUCTION –Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive sheave. MOTOR –1/2 HP–208/230/460/575V–3 PH. 60 Hz Totally Enclosed. CONVEYING SPEED –Constant 65 FPM. CAPACITY –150 lbs. total distributed live load. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –LS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above LS-6 support. BED LENGTHS –57 in. and 63 in. Drive not available on all lengths and widths. Contact factory. CONVEYING SPEED –Other constant and variable speeds from 25 to 120 FPM. NOTE : Capacity affected with speed change. SIDE MOUNTED DRIVE –Motor reducer unit mounted to side of conveyor. Minimum elevation with standard sheave retainer 11 1/16 in. O-RING DRIVE CHAIN –With sealed in lubricant (Recommended for applications that do not permit regular lubrication). GUARD RAILS –Adjustable Universal Channel Guard Rail, fixed channel, type A & B angle. (See Accessory section.) NOTE : If product comes in contact with guard rails, product flow will be affected. POLY-TIER SUPPORTS –36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGERS –5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. SLAVE DRIVEN –Standard drive may be omitted and spur slave driven from 138-ACC. (Specify by sketch, location of slave connection). Minimum elevation 10 1/2 in. MOTORS –Energy efficient, single phase, brakemotor, other characteristics. 1/2 HP maximum. ELECTRICAL CONTROLS –Non-reversing or reversible magnetic starters and push-button stations. AC variable frequency drive. Live Roller Spurs are used to transfer cartons, etc., onto and off of main conveyor lines. The illustrations below shows the correct usage of Plows and TurningWheels with Spurs in Diverging and Converging applications. • SPUR APPLICATIONS DIVERGING 30° most desirable transfer angle CONVERGING Both 30° and 45° are desirable transfer angles MOUNTING BRACKET The 138-LRSS is equipped with mounting brackets to attach unit to side channel of 138-ACC. SPUR FLOW (Specify) RH LH PRODUCT FLOW CORNER TURNING WHEEL 30˚ or 45˚ PRODUCT FLOW PLOW OR DEFLECTOR 30˚ MOUNTING BRACKET CONVEYOR SIDE CHANNEL SPUR CURVE CHANNEL • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy