Hytrol Catalog

CATALOG | 08312018 DCEZ-63 CHAIN –#60 single pitch conveyor chain (straight sidebar). CHAIN GUIDE – UHMW polyethylene. FRAME – 6 in. x 7 ga. powder painted formed steel angle with 1 1/2 in. x 3/16 wall, chain support tube. 4 ga. formed coupling channels located at infeed and discharge ends of each module. DRIVE SPROCKETS – Hardened #60 with 1 3/8 in. dia. steel shaft. BEARINGS – Sealed, pre-lubricated, self aligning, ball bearings on drive. ACCUMULATION ZONES –36 in., 42 in., 48 in., 54 in., 60 in., and 66 in. long intermediate sections with EZLogic ® Accumulation (Diffuse). Contact factory for other lengths. (Drive Section minimum 60 in. long.) EZLogic ® ZONE CONTROLLER–Located in each zone (Diffuse). NEMA 1, 2, IP62. UL Approved. IOP –Provides 27VDC, 100 watt power for EZLogic ® accumulation system - contains slots for 4 input/output boards. Requires 120VAC or 230VAC single phase input. AIR REQUIREMENTS – Recommended working pressure 60 P.S.I. Free air consumption at 75 P.S.I. - .50 cu. ft. per actuation for 18”& 21”strand centers - 1.0 cu. ft. per actuation for 24 - 28 strand centers. FILTER, REGULATOR –Supplied for main air supply line (1/2 in. NPT port). Includes pressure sensor. MOTOR –1 1/2 HP – 208/230/460/575V– 3 PH. 60 HZ. gearmotor, located underneath in 5 ft. long module. CONVEYING SPEED –35 FPM. CAPACITY –11,000 lbs. maximum at 30 FPM (1 1/2 HP maximum). NOT TO EXCEED CAPACITY IN CHART. FLOOR SUPPORTS –Now supplied as optional equipment. • OPTIONAL EQUIPMENT FLOOR SUPPORTS –DCDS and DC3S Type floor supports are available with a wide range of adjustment. Specify top of chain elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. CLOSED TAIL –Overall length will be affected. MOTORS –Energy efficient, 1 1/2 HP maximum. CONVEYING SPEED –Speeds other than 30 FPM will require geamotor change (contact factory). ELECTRICAL MOTORS CONTROLS –Non-reversing magnetic starter – push-button stations. EZLogic ® – See EZLogic ® Components Page. EZLOGIC ® ACCUMULATION SYSTEM Hytrol’s EZLogic ® , or “Electronic Zero-pressure Logic” Accumulation System, combines the sensing accuracy of photo- electronics with discrete electronic logic control without the use of a PLC or pneumatic logic components. The EZLogic ® Accumulation System provides many features including: Zero-Pressure Accumulation of Product Zone Stop - Function is built in. Any zone may be transformed into a workstation by connecting a dry contact switching device to the auxiliary port of the EZLogic ® Zone Controller. This feature is always used at the discharge end of the conveyor line, and may be used at any other location where a zone stop is required. Dynamic Zone Allocation – Automatically adjusts the conveyor’s zone length to accommodate the length of the product being conveyed. Improves conveyor efficiency and system flexibility. Unloading Zone Feature - Zone On Delay – Timer delays the zone immediately upstream from a removed load, preventing it from driving for a set time. This feature is ideal where loads are routinely removed from the conveyor with a lift truck. Loading Zone Feature – Zone detects load being placed onto the conveyor with a fork truck and stops the zone from driving and automatically prevents any loads in zones upstream from entering loading area. LOAD CAPACITY CHART (Accumulated or Live)* @ 30 FPM HP TOTAL LOAD (Lbs.) UP TO 50’ UP TO 102’ 1 1/2 11,000 10,000 *Load capacities in accumulation mode are calculated assuming no more than half of the load will be moving at any time. • STANDARD SPECIFICATIONS

RkJQdWJsaXNoZXIy NjQ0OTEy